Protector; Equipment Assembly - Tramontina AP300 Manual De Uso

Read the user and maintenance manual.
This equipment is indicated for occasional use (DoMEsTIc UsE).
Indicated for areas of up to 100m2 grass, to make shapes, edges and corners. This area can be larger
or smaller depending on the conditions of usage of the equipment: type of grass, height of the grass,
temperature, humidity, etc.
Use the trimmer with the protector (protective skirt) always. The protector helps in the refrigeration of the
motor and is a safety device for the operator. In the protector, the cutting blade is fixed that limits the length
of the nylon string, preventing overload and consequent burning of the motor.
imPortANt!
The use of the equipment without the protective skirt, as well as, the nylon string outside of the recommended
diameter, is considered as warranty loss.
Before turning on the equipment, check if the trimmer's voltage is set in accordance with the local electrical
voltage.
Assemble the protector [2] on the body [1], such that the three latches of the body fit into the notches of the
[Fig 1].

protector

Fix the protector to the body with the three safety screws [3].
Fit the puller into the metallic arm and regulate [4] to the most comfortable working position, attaching it with
the corresponding nut [5]
OpERatiOn
Before using the equipment, read carefully the usage and maintenance manual.
Before turning on the equipment, check if the trimmer's voltage is set in accordance with the local electrical
voltage.
For your security and to prevent the electric cable from being disconnected from the plug while the work is being
executed, bend the cable (1) and pass it through the opening (2)
then connect the electric cable to the plug of the grass trimmer.
The trimmer must be used with both hands. secure the grip with one hand and the handle with the other.
Keep the switch pressed down constantly during the work, avoiding oscillations of the rotation of the motor.
To turn off the trimmer, just release the switch.
The caliber of the electric cable must be in accordance with the table:
section in 127V
section in 127V
section in 127V
section in 127V
section in 127V
section in 127V
section in 127V
section in 127V
13
QuiCK Guide FOR usAGe

eQuiPMent AsseMBLy

[Fig 2].
OPeRAtiOn And FORM OF usAGe
10m 20m 30m
- 2 x 1mm² 2 x 1mm²
- 2 x 1mm² 2 x 1mm²
10m 20m 30m
2 x 1mm² 2 x 1mm² 2 x 1mm²
2 x 1mm² 2 x 1mm² 2 x 1mm²
10m 20m 30m
2 x 1mm² 2 x 1mm² 2 x 1,5mm²
2 x 1mm² 2 x 1mm² 2 x 1mm²
10m 20m 30m
2 x 1mm² 2 x 1mm² 2 x 1,5mm²
2 x 1mm² 2 x 1mm² 2 x 1mm²
[Fig 3]
AP300
40m 50m
2 x 1mm² 2 x 1mm²
2 x 1mm² 2 x 1mm²
AP500
40m 50m
2 x 1,5mm² 2 x 1,5mm²
2 x 1mm² 2 x 1mm²
AP600 and AP700
40m 50m
2 x 2,5mm² 2 x 2,5mm²
2 x 1mm² 2 x 1mm²
AP800 and AP1000
40m 50m
2 x 2,5mm² 2 x 2,5mm²
2 x 1mm² 2 x 1mm²
, then fit it in the clamp (3)
60m 80m
- -
- -
60m 80m
2 x 2mm² 2 x 2,5mm²
2 x 1mm² 2 x 1mm²
60m 80m
2 x 2,5mm² 2 x 4mm²
2 x 1mm² 2 x 1,5mm²
60m 80m
2 x 2,5mm² 2 x 4mm²
2 x 1mm² 2 x 1,5mm²
[Fig 4]
, only
100m
-
-
100m
2 x 4mm²
2 x 1,5mm²
100m
2 x 6mm²
2 x 1,5mm²
100m
2 x 6mm²
2 x 2,5mm²
Table 05