Publicidad
Idiomas disponibles
Idiomas disponibles
English
Performing an Application (Fig. A, I)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
"back-up" block to prevent damage to the material.
WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
1. Choose and install the appropriate chuck, adapter, and/
or bit onto to the tool. Refer to Bit and Bit Holder.
2. Using the mode selector dial
appropriate to desired application. Refer to
Operation Modes.
3. Adjust the side handle
3
4. Select the direction of rotation using the forward/
reverse button
. When changing the position of the
4
control button, be sure the trigger is released.
-
To select forward rotation, press the for ward/re verse
control button on the right side of the tool.
-
To select reverse, press the forward/reverse control
button on the left side of the tool.
nOTE: The center position of the control button
locks the tool in the off position.
Fig. K
6
3
5. Place the bit/chisel on the desired location.
6. Depress the trigger switch
the trigger switch, the faster the tool will operate. For
maximum tool life, use variable speed only for starting
holes or fasteners.
7. To stop the hammer, release the switch.
Recommendations for Tool Operation
•
Large (5/16" to 1/2" [7.9 mm to 12.7 mm]) holes in steel
can be made easier if a pilot hole (5/32" to 3/16" [4 mm
to 4.8 mm]) is drilled first.
•
When drilling, always apply pressure in a straight line
with the bit, but do not push hard enough to stall the
motor or deflect the bit. A smooth even flow of material
indicates the proper drilling rate.
•
If drilling thin material or material that is prone to
splinter, use a wood "back-up" block to prevent damage
to the work piece.
WARNING:
•
Do not use this tool to mix or pump easily
combustible or explosive fluids (benzine,
alcohol, etc.).
•
Do not mix or stir inflammable liquids
labelled accordingly.
10
6
, select the mode
as necessary.
5
4
5
. The farther you depress
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by D
WALT, have not been tested with this
E
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Various types of SDS Plus drill bits and chisels are available
as an option. Accessories and attachments used must be
regularly lubricated around the SDS Plus fitment.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
WALT (1-800-433-9258) or visit our website:
E
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D
WALT factory service center
E
or a D
WALT authorized service center. Always use
E
identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
•
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
•
COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
WALT
E
WALT Industrial
E
Publicidad
