JVC WR-MG300 Manual De Instrucciones página 17

WR-MG270_EN.book Page 17 Wednesday, March 24, 2010 1:36 PM
Attaching the Marine Case to the
Camera
Setup the camera.
A
For models equipped with light, turn off the
Attaching the Marine Case to the
light.
Camera
Open the lens cover.
Set to the shooting mode (video/still
Setup the camera.
A
image).
For models equipped with light, turn off the
Even when the shooting mode is set to
light.
"video", still images can be captured by
Open the lens cover.
pressing the still image lever during video
Set to the shooting mode (video/still
recording. (For selected models.)
image).
It is recommended to set to the auto
Even when the shooting mode is set to
shooting mode.
"video", still images can be captured by
Insert the battery and the microSD/
pressing the still image lever during video
microSDHC card or SD/SDHC card
recording.
beforehand if needed.
It is recommended to set to the auto
l Please set "Auto power-off" mode to "off"
To turn off the camera, press and hold the
shooting mode.
power button for more than 2 seconds.
from the Camcorder setting menu, the
Insert the battery and the microSD/
Camcorder has no power button.
Insert the drying agent at the back of the
microSDHC card or SD/SDHC card
B
l To turn off the camera, press and hold the
base. beforehand if needed.
power button for more than 2 seconds.(For
To turn off the camera, press and hold the
2 Catch
power button for more than 2 seconds. selected models.)
Insert the drying agent at the back of the
B
base.
2 Catch
1 Pass underneath
Attach the base to the bottom of the
C
camera.
Align the tripod screw hole at the bottom of
1 Pass underneath
your camera with the screw of the base,
and tighten the screw.
Attach the base to the bottom of the
C
camera.
Tighten the screw
2
Align the tripod screw hole at the bottom of
your camera with the screw of the base,
and tighten the screw.
Tighten the screw
2
Caution
The camera turns on automatically when the
LCD monitor is opened. To turn off the camera,
press and hold the power button for more than
2 seconds.
Caution
The camera turns on automatically when the
LCD monitor is opened. To turn off the camera,
press and hold the power button for more than
2 seconds.
Drying agent
Drying agent
1 Open up the LCD monitor
1 Open up the LCD monitor
Fold the grip belt.
D
Make sure the grip belt is not caught
between the marine case when sealing.
Open the marine case.
E
If it is difficult to open buckles, use the
Fold the grip belt.
D
small hexagonal wrench (buckle opener).
Make sure the grip belt is not caught
between the marine case when sealing.
Open the marine case.
E
If it is difficult to open buckles, use the
small hexagonal wrench (buckle opener).
Small hexagonal wrench
(Buckle opener)
Attach the power button cap.
F
(Not required for GZ-HM545 to GZ-HM570.)
Fit the hollow of the power button cap to
Small hexagonal wrench
the protrusion of the power button on the
(Buckle opener)
case.
Attach the power button cap.
F
(Not required for GZ-HM545 to GZ-HM570.)
Fit the hollow of the power button cap to
the protrusion of the power button on the
case.
❻
Insert the camera into the marine case.
G
Align the base attachment groove with the
base to insert.
Insert the camera into the marine case.
G
Align the base attachment groove with the
base to insert.
Base attachment groove
Base
Marine case internal base
Base attachment groove
❼ Base
Adjust the angle of the LCD monitor.
H
The LCD monitor can be tilt upwards to a
Marine case internal base
maximum angle of 30 degrees.
Adjust the angle of the LCD monitor.
H
The LCD monitor can be tilt upwards to a
maximum angle of 30 degrees.
Power button cap
Power button cap
17