Publicidad
Idiomas disponibles
Idiomas disponibles
disconnecting the supply. Do not use the product if
the cord is damaged or worn.
■
If the power cord is damaged, it should be replaced
by a person professionally qualified to do so, with a
new cable set that is available from the manufacturer.
Failure to follow this instruction can result in serious
injury to yourself or others including electrocution.
■
If you need to use an extension cord ensure that it is
suitable for outdoor use and has a current capacity
rating sufficient to supply your product. The extension
cord cable should be marked with either "H05 RN-F"
or "H05 VV-F". Check the cord before every use for
damage, and always uncoil it during use, because
coiled cords can overheat. Replace damaged extension
cords with an equivalent type. Do not repair damaged
extension cords.
■
Make sure to keep extension cords away from moving
hazardous parts to avoid damages to the cords which
can lead to contact with live parts.
■
Make sure that the power cord is positioned so that it
cannot be damaged by the cutting means and will not
be stepped on, tripped over or otherwise subjected to
damage or stress.
■
Never pick up or carry the product by the electric cable.
■
Never pull by the power cord to disconnect from the
power supply.
■
Keep the power cord away from heat, oil and sharp
edges.
■
Make sure that voltage is correct for your product.
A nameplate on the product indicates the product's
voltage. Never connect the product to an AC voltage
that differs from this voltage.
■
Always ensure that the cord from the handlebar to the
scarifier body is never trapped, pinched or otherwise
damaged during assembly or handle folding. Never
apply power to the product if the cable is damaged.
Have the product serviced by an authorised service
centre only.
■
A power spike causes voltage fluctuations and
may affect other electrical products in the same
power line. Connect the product to a power supply
with an impedance equal or less than 0.452Ω - for
RY1400SF35A and RY1400SF35B to minimize voltage
fluctuations. Contact your electric power supplier for
further clarification.
ELECTRIC SCARIFIER AND AERATOR SAFETY
WARNINGS
■
The tines on the product are sharp. Use extreme
caution and wear heavy-duty gloves when fitting,
replacing, cleaning, or checking bolt security.
■
Check that all screws, nuts, bolts, and other fasteners
are properly secured and that guards and screens are
in place. Replace damaged or unreadable labels.
■
Replace worn or damaged parts before operating the
product.
■
Install the debris collector before scarifying. Empty
the debris collector when it is full and reinstall before
resuming operation.
2
| English
■
The product must be started with the user behind the
handlebars in the operator safety zone. Never start the
product if:
●
not all four wheels are on the ground
●
the debris discharge chute is exposed and is
not protected by the debris collector and debris
discharge chute cover.
■
Never operate the product if the on/off switch on the
handlebar does not properly start and stop the product.
■
Never lock the on/off switches in the on position; this is
extremely dangerous.
■
Do not force the product. It will do the job better and
safer at the speed for which it was designed.
■
Stop the tines when crossing gravel surfaces.
■
Use extreme caution when reversing or pulling the
product towards you.
■
Stop the tines if the product has to be tilted for
transportation when crossing surfaces other than
grass, and when transporting the product to and from
the work area.
■
Never use the product with defective guards or shields,
or without safety devices, for example, deflectors and/
or debris collectors, in place.
■
Do not tilt the product when turning on the motor, except
if the machine has to be tilted for starting. If absolutely
necessary, you may lift only the part that is away from
the operator. Always ensure that both hands are in the
operating position before returning the machine to the
ground.
■
Turn on the product carefully according to the
instructions and keep hands and feet away from the
tines. Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all times.
■
Never pick up or carry the product while it is running.
■
Keep the supply and extension cord away from tines.
■
Turn off the product, and disconnect it from the power
supply. Make sure that all moving parts have come to
a complete stop:
●
whenever you leave the product unattended
(including disposal of grass clippings).
●
before cleaning a blockage or unclogging the
discharge chute
●
before checking, cleaning or working on the product
●
after striking a foreign object; inspect the product
for damage and make repairs as necessary before
restarting and operating the product.
■
If the product starts to vibrate abnormally, check
immediately to:
●
inspect for damage
●
replace or repair any damaged parts
●
check for and tighten any loose parts
■
Avoid holes, ruts, bumps, rocks, property stakes, or
other hidden objects. Uneven terrain could cause a
slip-and-fall accident.
■
Release the handle immediately and stay away from
the product if:
●
the product catches fire
●
the guard and/or housing is broken
Publicidad
