Homelite HL80220 Manual Del Operador página 14

WARNING:
If any parts are damaged or missing do not operate this prod-
uct until the parts are replaced. Use of this product with dam-
aged or missing parts could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories
not recommended for use with this product. Any such altera-
tion or modification is misuse and could result in a hazardous
condition leading to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly is complete.
Failure to comply could result in accidental starting and
possible serious personal injury.
INSTALLING THE WHEELS
See Figure 4.
 Locate the axles, hitch pins, washers, and wheels.
 Slide the axle through the hole in the center of the wheel.
 Lift the machine and slide the axle into the wheel mounting
hole in the machine base as shown.
 Slide the washer on the axle, then push the hitch pin into the
hole on the end of the axle to secure the wheel assembly.
NOTE: The hitch pin should be pushed into the axle until
the center of the pin rests on top of the axle.
 Repeat with the second wheel.
ATTACHING THE HANDLE ASSEMBLY
See Figure 5.
 Orient the handle assembly as shown.
 Depress the button on the handle assembly and insert into
the holes on the pressure washer. Press down on the handle
assembly until the button on the handle clicks into place.
 Lower both collars on the handle and rotate clockwise until
secure.
ASSEMBLING THE SPRAY WAND
See Figure 6.
 Push the two ends of the spray wand together so that the
holes inside each end are aligned.
 Lower the locking collar and rotate counterclockwise until
you hear the clicking sound, which indicates the wand is
securely tightened.
 Place the assembled spray wand in the spray wand holder
with the notched area resting on the pressure washer handle.
ATTACHING THE HIGH PRESSURE AND
LOW PRESSURE HOSES TO THE TRIGGER
HANDLE
See Figure 7.
 The low pressure hose is the clear tube with the plastic fitting
and goes on the spout at the bottom of the trigger handle.
 Grasp the plastic fitting and slide onto the spout until it
clicks into place.
ASSEMBLY
 To remove, depress the latch on top of the fitting and
remove the hose from the spout.
 The high pressure hose has a metal connection and slides
into the opening at the top of the trigger handle.
 Grasp the hose lock and pull outward to clear the way
for the high pressure hose to be inserted.
 Insert the high pressure hose all the way into the hole.
 Push the hose lock fully back into the handle to hold the
high pressure hose in place.
CONNECTING THE GARDEN HOSE
See Figures 8 - 10.
CAUTION:
Always observe all local regulations when connnecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water sup-
ply to prevent the feedback of chemicals into the drinking
water supply. Direct connection through a receiver tank
or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose:
 Uncoil the garden hose.
NOTE: There must be a minimum of 10 feet of unrestricted
garden hose between the water intake and the garden hose
faucet or shut off valve (such as a "Y" shut off connector).
 Run water through the garden hose for 30 seconds to clean
any debris from the hose.
To connect the garden hose to the machine through G-Clean
detergent injector:
 Loosen bracket screws and remove bracket.
 Rotate the G-Clean detergent injector counterclockwise to
loosen and remove.
 Disassemble injector as described in the Using the Deter-
gent Injector section of the manual. Ensure that the G-Clean
detergent injector screen is not damaged or clogged. Clean
or replace as needed.
 Inspect the filter screen in the water intake.
 If the screen is damaged, do not use the machine until
the screen has been replaced.
 If the screen is dirty, clean it before connecting the garden
hose to the machine.
 Reassemble injector, return it to unit, and replace bracket.
 With the garden hose faucet turned completely off, attach
the end of the garden hose to the G-Clean detergent injec-
tor. Tighten by hand.
To connect the garden hose directly to the machine:
 Remove the G-Clean injector.
 Inspect the filter screen in the water intake. Clean or replace
as needed.
 With the garden hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by hand.
Page 10 — English