LEGRAND Wattstopper LMSW-105-U Guia De Inicio Rapido

No: 23272 – 05/21 rev. 2
Catalog Number • Numéro de Catalogue • Número de Catálogo: LMSW-105
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
LMSW-105-U is BAA and TAA compliant (Product produced in the U.S.)
This unit is pre-set for Plug n' Go™ operation,
adjustment is optional.
For full operational details, adjustment and more features
of the product, see the DLM System Installation Guide
provided with Wattstopper room controllers, and also
available at www.legrand.us/wattstopper.
Installation shall be in accordance with all applicable
regulations, local and NEC codes. Wire connections shall
be rated suitable for the wire size (lead and building wiring)
employed.
For Class 2 DLM devices and device wiring: To be
connected to a Class 2 power source only. Do not reclassify
and install as Class 1, or Power and Lighting Wiring.
Do not apply cleaning solvent directly onto unit. Apply
cleaning solvent onto a cloth, then wipe the unit to clean it..
MOUNTING THE SWITCH
WARNING: Do not install to cover a junction box having Class 1, 3 or
Power and Lighting Circuits.
The illustrations show examples of free-topology wiring. The LMSW-105 communicates with all other Digital Lighting Management
devices connected to the low voltage DLM Local Network.
LMDM-101 LMSW-105
Occupancy Sensor
Dimming Switch Scene Switch
LMDM-101
Dimming Switch
LMRJ Cables
CAUTION: TO CONNECT A COMPUTER TO THE DLM LOCAL NETWORK USE THE LMCI-100.
NEVER CONNECT THE DLM LOCAL NETWORK TO AN ETHERNET PORT –
IT MAY DAMAGE COMPUTERS AND OTHER CONNECTED EQUIPMENT.
Line Voltage
Class 2 0-10 Volt Control Wiring
LMRC-212
Line Voltage
Dimming 0-10 Volt
Ballast
Room
Controller
J-Box
0-10 Volt
Ballast
Wattstopper
Digital Lighting Management Low Voltage Scene Switch (v3)
Interrupteur d'ambiance à basse tension (v3)
Interruptor de escena de bajo voltaje de control de iluminación digital (v3)
Quick Start Guide • Guide de démarrage rapide • Guía de inicio rápido
Voltage .............................................................................. 24VDC
Current Consumption .............................................................5mA
Power Supply ................Watt Stopper/Legrand Room Controllers
Connection to the DLM Local Network .................... 2 RJ-45 ports
DLM Local Network characteristics when using LMRC-11x/2xx
room controllers:
Low voltage power provided over Cat 5e cable (LMRJ);
max current 800mA. Supports up to 64 load addresses,
48 communicating devices including up to 4 LMRC-10x
series and/or LMPL-101 controllers.
Free topology up to 1,000' max.
Environment ................................................. For Indoor Use Only
Operating Temperature .................32° to 131°F (0° to 55°C)
Storage Temperature ...................23° to 176°F (-5° to 80°C)
Relative Humidity .......................5 to 95% (non condensing)
Patent Pending
Tap when load OFF:
Turn ON to last level
Tap when load ON:
Go to full bright
Press & Hold:
Ramp Up
Tap when load ON:
Turn OFF
Press & Hold:
Ramp Down
When all loads bound to the dimmer paddle are OFF, it's
Blue status LED is dim. When any load bound to the dimmer
paddle is ON it's Blue status LED is bright.
When a scene is active the LED on the scene button is bright.
CONNECTIVITY
Daylighting
Sensor
®
SPECIFICATIONS
BUTTONS AND INDICATORS
Corner Mount
Occupancy
Sensor
J Box
LMRC-21x
Room
Controller
To
Load
To 0-10V
Dimming Ballast
Blue Status LEDs
Scene Button (4)
Configuration Button
(behind switch plate)
Red LED
DLM Local Network
(low voltage, Class 2)
LMRJ cables
Ceiling Mount
Occupancy
Switch/
Sensor
Dimmer