EINHELL GH-EC 1835 Manual De Instrucciones página 24

sition and only use the chainsaw when
you are standing on a solid, safe and flat
surface. Slippery or unsafe surfaces in com-
bination with a ladder can cause you to lose
your balance and control over the chainsaw.
•
When cutting through a branch which is
under tension, take into account how it
will spring back once the cut has been
made. Once the tension in the wood fibers is
released, the tensioned branch could hit the
operator and/or seize control of the chainsaw.
•
Take special care when cutting underg-
rowth and young trees. The thin material
can become caught in the saw chain and
whip back towards you or make you lose your
balance.
•
Carry the chainsaw by the front handle
with the chainsaw switched off and the
chain facing away from the body. Always
fit the protective cover when transporting
the chainsaw or putting it into storage.
Careful handling of the chainsaw reduces the
likelihood of accidental contact with the saw
chain while it is running.
•
Follow the instructions for lubrication,
chain tension and replacement of ac-
cessories. A chain which is not properly
tensioned or lubricated can either break or
increase the risk of kickback.
•
Keep the handles dry, clean and free from
oil and grease. Greasy or oily handles are
slippery and will result in loss of control.
•
Only use the chainsaw to cut wood. The
chain must only be used to perform the
work for which it is intended. For examp-
le: Never use the chainsaw to cut plastic
or brickwork or building materials which
are not made of wood. Use of the chainsaw
for non-intended or non-approved work can
create dangerous situations.
•
Hold the appliance only by the insulated
handles when carrying out work during
which the cutting tool could strike conce-
aled power cables or its own cable. Con-
tact with a live cable will also make the metal
parts of the appliance live and will cause an
electric shock.
Causes of and ways to avoid recoil
Recoil can occur if the tip of the chain bar touches
an item or if the wood bends and jams the saw
chain in the cut.
In many cases contact with the bar tip can result
in an unexpected reaction aimed backwards in
Anl_SA_GH_EC_1835_SPK8.indb 24 Anl_SA_GH_EC_1835_SPK8.indb 24
GB
which the chain bar is catapulted upwards to-
wards the operator.
Jamming the saw chain on the top of the chain
bar can catapult the bar towards the operator at
high speed.
Any of these reactions can result in you losing
control over the saw and possibly suff ering seri-
ous injuries. You should therefore not rely totally
on the safety equipment fi tted to the chainsaw.
When using a chainsaw you should take various
precautions to enable you to work without suff e-
ring accidents or injuries.
Recoil is the result of incorrect or wrong use of
the electric tool. It can be prevented by suitable
precautions, as described below:
•
Hold the saw firmly with both hands, with
fingers and thumbs gripped around the
handles. Steady yourself with your body
and arms in a position in which you can
control the kickback forces. Provided ap-
propriate measures are taken, an operator
should be capable of controlling the kickback
forces. Never let go of the chain saw.
•
Avoid abnormal working postures. Never
cut above shoulder height. This prevents
accidental contact with the tip of the rail and
offers better control over the chainsaw in un-
expected situations.
•
Always use the correct replacement rails
and saw chains recommended by the ma-
nufacturer. The use of incorrect replacement
rails or saw chains may result in breakage of
the chain and/or kickback.
•
Follow the manufacturer's instructions
for sharpening and maintaining the saw
chain. The risk of kickback is increased if the
depth limiter is set too low.
More important information:
•
Use an earth-leakage circuit breaker with a
trip current of 30 mA or less.
•
Position the power cable such that it cannot
be caught by branches or the like during sa-
wing.
•
We recommend that first-time users should at
least practice cutting roundwood (logs) on a
sawing trestle or similar.
Residual risks
Even if you use this electric power tool in ac-
cordance to instructions, certain residual risks
cannot be eliminated. The following hazards may
arise in connection with the equipment's const-
- 24 -
04.05.16 12:46 04.05.16 12:46