Husky HDS780 Manual De Instrucciones página 2

See Warranty on page 7 for important information about commercial use of this product.
Operating Instructions and Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or prop-
erty damage! Retain instructions for future reference.
Description
A gravity feed spray gun is designed
to spray all light to medium viscosity
materials. Enamels, lacquers,
polyurethane, urethane top coats
(including basecoat/clearcoat) and all
primers can be applied. The spray gun
has fluid, pattern and air controls. This
spray gun is supplied with a 20.3 oz
(600 ml) gravity feed cup.
Specifications
Air Required
(SCFM @ 40 psi) . . . .5.9 Ave. (70% Duty)
Fluid Nozzle Size . . . . 0.055 in. (1.4 mm)
Fluid Delivery Speed . . . . . Medium-Fast
Feed Type. . . . . . . . . . . . . . . . . . . Gravity
Mix Type . . . . . . . . . . . . . . . . . . External
Bleed Type . . . . . . . . . . . . . . Non-Bleeder
Normal Inlet
Air Pressure . . . . . . . . . . . . . . .40-50 psiG
Max. Inlet
Air Pressure . . . . . . . . . . . . . . . . . 80 psiG
Cup Size . . . . . . . . . . . . . 20.3 oz (600 ml)
Safety Guidelines
This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS.
To help recognize this information,
observe the following symbols.
an imminently hazardous situation
which, if not avoided, WILL result in
death or serious injury.
cates a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
cates a potentially hazardous situation
which, if not avoided, MAY result in
minor or moderate injury.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2008
important information, that if not fol-
lowed, may cause damage to equipment.
Unpacking
After unpacking the product, inspect
carefully for any damage that may
have occurred during transit. Make
sure to tighten fittings, bolts, etc.,
before putting unit into service.
tool if damaged during shipping, handling
or use. Damage could result in bursting
and cause injury or property damage.
8.5 Continuous
General Safety
Information
CALIFORNIA PROPOSITION 65
You can create dust when
you cut,
or grind materials such as
wood, paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to cause
cancer, birth defects, or other reproduc-
tive harm. Wear protective gear.
GENERAL SAFETY INFORMATION
1. Read all manuals includ-
ed with this product
carefully. Be thoroughly
familiar with the con-
trols and the proper use
of the equipment.
Danger
2. Follow all local electrical and safety
indicates
codes as well as the United States
National Electrical Codes
(NEC) and Occupational Safety and
Warning
Health Act (OSHA).
indi-
Use a face mask/respira-
tor and protective clothing
Caution
when spraying. Always
indi-
spray in a well ventilated area to pre-
vent health and fire hazards. Refer to
Material Safety Data Sheets (MSDS) of
spray material for details.
Gravity Feed Spray Gun
Notice
indicates
Do not
operate
sand, spray, drill
MANUAL
Never spray closer than 25
feet to the compressor! If
possible, locate compres-
sor in separate room. Never
spray into the compressor, compressor
controls or the motor.
3. Do not smoke or eat when spraying
paint, insecticides, or other flam-
mable substances.
Do not spray flammable
materials in vicinity of open
flame or near ignition sourc-
es. Motors, electrical equipment and
controls can cause electrical arcs that
will ignite a flammable gas or vapor.
Never store flammable liquids or gases
in the vicinity of the compressor.
this product. Excessive exposure to vibra-
tion, work in awkward positions, and
repetitive work motions can cause injury
to hands and arms. Stop using any tool
if discomfort, numbness, tingling or pain
occur, and consult a physician.
4. When spraying and cleaning, always
follow the instructions and safety
precautions provided by the mate-
rial manufacturer (Refer to MSDS).
acids, corrosive materials, toxic chemi-
cals, fertilizers or pesticides. Using
these materials could result in death or
serious injury.
5. Keep visitors away and NEVER allow
children or pets in the work area.
spray at yourself or anyone else or seri-
ous injury could occur.
6. Always work in a clean environ-
ment. To avoid injury and damage
to the workpiece, do not aim the
spray gun at any dust or debris.
Do not use pressure that
exceeds the operating pres-
sure of any of the parts (hoses,
fittings, etc.) in the painting system.
IN285600AV 2/08
HDS780
Do not
misuse
Do not
spray
Never
aim or