Publicidad
Idiomas disponibles
Idiomas disponibles
EN
3. Getting Started
3.1 Powering the Baby Unit (Camera)
•
Connect the Camera Power Adapter to the DC-Jack (26) on the back bottom of the Baby Unit.
•
Plug the AC power adapter into the wall outlet.
•
Ensure the ON/OFF switch (25) is in the ON position.
The unit will power on automatically and the green power LED (3) will light up.
•
•
Use the ON/OFF switch (25) to turn the Baby Unit off.
NOTE: Only use the AC power adapter included in this package.
3.2 Powering the Parent Unit
•
The adapter should not be exposed to direct heat sources such as a candle, stove, radiator, heat register or other appliance that emit heat.
•
Connect the Parent Unit Power Adapter to the DC-Jack (16) on the right side of the Parent Unit.
•
Plug the AC power adapter into the wall outlet.
•
Press and hold the Power button (1) on the top left side of the Parent Unit for 2 seconds to turn the unit on.
Once the Parent Unit is turned on, the green power LED (3) will light up and "Babysense Video" logo will display on the LCD.
•
•
Press and hold the Power button (1) on the top left side of the Parent Unit for 5 seconds to turn the unit off.
NOTE: Only use the AC power adapter included in this package.
NOTE: The Parent Unit is supplied with a built-in rechargeable Li-ion battery (3.7V 4000mAh).
We recommend whenever possible, keep the Parent Unit plugged in to keep the battery charged.
3.3 Charging the Parent Unit
•
Connect the power adapter to the DC-Jack (16) on the right side of the Parent Unit.
•
Plug the AC power adapter into the wall outlet.
•
Charging LED (2) on the Parent Unit will light up in RED to indicate charging.
•
When the unit is turned on, the battery charging icon (changing bars) will appear at the top right corner of the LCD screen.
•
Full battery indicator (4 fixed bars) will appear at the top right corner of the LCD screen, indicating the battery is fully charged. The charging
8
LED (2) will turn green once the battery is fully charged.
NOTE: Before the first use or after a long product storage, it is recommended to fully charge the Parent Unit prior to operating the monitor. It
takes approximately 8 hours to fully charge the battery.
NOTE: The monitor can be operated normally during the charging process.
NOTE: Low Battery Warning - The battery icon turns red on the LCD screen to indicate that the battery is low. The warning is accompanied
with an acoustic beep sound, indicating that the battery needs to be recharged. *
* Alert Volume can be adjusted in the Parent Unit menu, see details in Section Warning Alert" Volume Setting".
3.4 Set Up
•
Once both the Baby and Parent Units are switched on, the display on the Parent Unit will show the video captured by the Baby Unit(s).
•
Baby Unit(s) are paired to the Parent Unit when supplied. There is no need to pair the units again unless the Baby Unit loses its link with the
Parent Unit. To renew the pairing of your units or pair a new/additional Baby Unit, follow the procedure described in "Section 4.4 Pairing the
Baby Unit (Camera) with the Parent Unit".
•
The Baby Unit should be placed at least 6 feet away from the baby's crib on a flat surface. Alternatively, it can be wall mounted.
•
Never place the Baby Unit inside the crib, bed or playpen.
• Make sure the unit and cords are out of reach of the baby and other young children.
• To avoid a strangulation hazard, the power cords should be secured and never hung on the crib or near the baby.
•
Place the baby monitor in a place where the air can circulate freely and avoid blocking the ventilation and speaker openings.
•
Aim the camera (s) to best optimize the viewing area: Select a location for the camera that provides a clear view of the area you want
to monitor, which is free from dust, and is not in line-of-sight to a strong light source or direct sunlight. Avoid installing the camera where
there are thick walls or obstructions between the camera and the monitor.
•
To use your Parent Unit and Baby Unit together, you must be able to establish a radio link between them; the range may be affected by
environmental conditions/obstacles (See more details in Troubleshooting Section 6 - "Interference or poor reception")
4. Operating the Monitor
4.1 Lullaby & White Noise Setting
You can soothe your baby to sleep by playing 5 pre-programmed lullabies from the Baby Unit.
The monitor also features White Noise, which is an effective way to soothe a crying infant and lull your newborn to sleep. The Lullaby and White
Noise features are is controlled remotely from the Parent Unit.
EN
9
Publicidad
