Shure LEGENDARY PERFORMANS GLX-D Manual Do Usuário página 10

2.4 GHz Frequency Tables
The following tables list receiver channels, frequencies, and latency for each group:
Group 1: Channels 1-4 (latency = 4.0 ms)
Group/Channel Frequencies
1/1 2424 2425 2442 2443 2462 2464
1/2 2418 2419 2448 2450 2469 2471
1/3 2411 2413 2430 2431 2476 2477
1/4 2405 2406 2436 2437 2455 2457
Group 3: Channels 1-8 (latency = 7.3 ms)
Group/Channel Frequencies
3/1 2415 2416 2443
3/2 2422 2423 2439
3/3 2426 2427 2457
3/4 2447 2448 2468
3/5 2409 2451 2452
3/6 2431 2462 2463
3/7 2404 2473 2474
3/8 2435 2477 2478
Receiver Operation
Audio Gain Adjustment
Transmitter gain has an adjustment range from -20 dB to +40 dB, in 1 dB
increments.
Tip: Try the 0 dB (unity gain) setting as a starting point, and then make gain adjust-
ments if necessary.
1. Press and hold the mode button on the re-
ceiver until dB appears on the display.
2. Press the up/down arrows to adjust the gain. For fast-
er adjustments, press and hold the buttons.
audio
Note: The intensity of the green
flashing indicates audio clipping. Reduce the gain to remove the overload.
Locking and Unlocking the Controls
The controls of the receiver and transmitter can be locked to prevent accidental or unauthorized changes to settings.
The following parameters are not affected by locking the controls:
• Lock status is not changed by power cycles
• Tuner functionality and editing remains available
• The receiver power switch does not lock
Locking the Receiver Controls
Simultaneously press and hold the group and channel buttons to lock or
unlock the receiver.
• LK is displayed if a locked control is pressed
• UN is displayed momentarily to confirm the unlock command
Remote ID
Use the Remote ID feature to identify linked transmitter and receiver pairs. When Remote ID is active, the receiver LCD will blink and display ID. The
status LED of the corresponding transmitter will alternately flash red and green for approximately 45 seconds.
To activate Remote ID:
1. Momentarily press the link button on the transmitter or receiver.
2. The display of the linked receiver will blink and show ID and
the status LED on the linked transmitter will flash red/green.
3. To exit Remote ID mode, momentarily press the
link button or allow the function to timeout.
10
LED corresponds to the audio level. Rapid
Group 2: Channels 1-5 (latency = 7.3 ms)
Group/Channel Frequencies
2/1 2423 2424 2443 2444 2473 2474
2/2 2404 2405 2426 2427 2456 2457
2/3 2410 2411 2431 2432 2448 2449
2/4 2417 2418 2451 2452 2468 2469
2/5 2437 2438 2462 2463 2477 2478
Group 4: Channel 1 (latency = 7.3 ms)
Group/Channel Frequencies
4/1 2404 2405 2410 2411 2417 2418 2423 2424
2426 2427 2431 2432 2437 2438 2443 2444
2448 2449 2451 2452 2456 2457 2462 2463
2468 2469 2473 2474 2477 2478
link group
mode audio mute rf channel
Locking the Transmitter Power Switch
Starting with the transmitter set to off, press and hold the LINK button
while turning on the transmitter. Repeat sequence to unlock.
Note: The transmitter status LED will flash red/green if a locked switch is set to the
off position.
link group
mode audio mute rf channel