Publicidad
Idiomas disponibles
Idiomas disponibles
•
On/off 6
•
Maximum speed control 7
- With wheel B the maximum speed can be adjusted
from low to high
•
Selecting operating mode 8
! select operating mode only when tool is switched
off and plug is disconnected
- press button C to unlock switch D
- first turn switch D to the desired operating mode until it
snap-locks
- then turn switch E to the desired operating mode
1 = normal drilling
2 = impact drilling
3 = chiseling
! start working only when switch D is locked
- for drilling in wood, metal and plastic the corresponding
adapter should be used (see: Application Advice)
- the hammer mechanism is activated by applying a
slight pressure on the tool when the drill bit is in contact
with the workpiece
- it takes a short time for the hammer mechanism to
reach full impact power
- do not apply too much pressure on the tool; let the tool
do the work for you
Changing bits 9
•
! clean and lightly lubricate the SDS+ accessory
before insertion
- pull back locking sleeve F and insert accessory
in SDS+ chuck while turning and pushing it until it
engages; the accessory locks in position automatically
- pull accessory to check that it is locked correctly
- remove accessory by pulling back locking sleeve F
! the SDS+ accessory requires freedom of
movement which causes eccentricity when tool
is off-load; however, the accessory automatically
centres itself during operation without affecting
drilling precision
! do not use bits/chisels with a damaged shank
•
Safety clutch
if the accessory gets jammed, the drive to the spindle is
interrupted (causing a rattling noise)
- immediately switch off tool
- remove the jammed accessory
- switch on tool again
•
Adjusting drilling depth q
•
Holding and guiding the tool w
! while working, always hold the tool at the grey-
coloured grip area(s)
- always use auxiliary handle G (can be adjusted as
illustrated)
- keep ventilation slots H 2 uncovered
APPLICATION ADVICE
•
Use the appropriate bits e
! only use sharp bits/chisels
•
For drilling in wood, metal and plastic use the
corresponding adapter r
- clean and lightly lubricate adapter before insertion
- pull back locking sleeve F 2 and insert adapter
in SDS+ chuck while turning and pushing it until it
engages; the adapter locks in position automatically
- pull adapter to check whether is it locked correctly
- set switch D 2 to normal drilling (only activate when
tool is switched off and plug is disconnected)
•
When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
•
Splinterfree drilling in wood t
•
Dustfree drilling in walls y
•
Dustfree drilling in ceilings u
•
Drilling in tiles without skidding i
•
For more information see www.skil.com
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
•
Never open the tool yourself o
•
Always keep tool and cord clean (especially ventilation
slots H 2 )
! disconnect the plug before cleaning
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
•
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
Only for EU countries
Do not dispose of electric tools, accessories and
•
packaging together with household waste material
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
Only for UK
•
Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of on Waste Electric and Electronic
Equipment Regulations 2013 (SI 2013/3113), electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
- prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
NOISE / VIBRATION
•
Measured in accordance with EN 62841 the sound
pressure level of this tool is 94.0 dB(A) and the sound
power level 105.0 dB(A) (uncertainty K = 3 dB), and the
vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)
when hammer drilling in concrete 18.7 m/s²
✱
12
Publicidad
