Poulan Pro 220 Manual De Instrucciones página 10

ON/STOP
Switch
ON/STOP SWITCH
oNr --I@
CHOKE/FAST IDLE LEVER
_ (SIDE VIEW)
Choke/Fast OFF FULL
Idle Lever
STARTING A WARM ENGINE:
1. Move ON/STOP switch to the ON posi-
tion.
2. Pull the choke/fast idle lever out to the full
extent, then push the lever back in com-
pletely (to the OFF position).
3. Slowly press the primer bulb 6 times.
4. Pull the starter rope quickIy with your
right hand until the engine starts.
5. Squeeze and release throttle trigger, al-
lowing engine to idle.
DIFFICULT STARTING (or starting a
flooded engine):
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ON/
STOP switch is in the ON position.
Starting could require pulling the starter rope
handle many times depending on how badly
the unit is flooded. If engine fails to start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
CHAIN BRAKE
WAR NIN G:
if the brake band is
worn
too thin it may break when the chain brake is
triggered. With a broken brake band, the chain
brake will not stop the chain, The chain brake
should be replaced by an authorized service
dealer if any part is worn to less than 0,020"
(0.5 mm) thick, Repairs on a chain brake
should be made by an authorized service deaf
er. Take your unit to the place of purchase if
purchased from a servicing dealer, or to the
nearest authorized master service dealer.
• This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
• The inertia-activated chain brake is
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
• If the brake is already activated, it is
disengaged by pulling the front hand guard
back toward the front handle as far as
possible.
• When cutting with the saw. the chain brake
must be disengaged.
Disengaged
_
Braking function control
CAUTION: The chain brake must be
checked several times daily. The engine
must be running when performing this proce-
dure. This is the only instance when the saw
should be placed on the ground with the en-
gine running.
Place the saw on firm ground. Grip the rear
handle with your right hand and the front han-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
Inertia activating function control
_,WARNING:
When performing the
following procedure, the engine must be
turned off.
G rip the rear handle with your right hand and
the front handle with your left hand, Hold the
chain saw approximately 14" (35 cm) above
a stump or other wooden surface, Release
your grip on the front handle and use the
weight of the saw to let the top of the guide
bar fall forward and contact the stump.
When the tip of the bar hits the stump, the
brake should activate.
IMPORTANT POINTS
• Check chain tension before first use and
after 1 minute of operation. See CHAIN
TENSION in the ASSEMBLY section.
• Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials,
etc.
• Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary.
• Keepthechainoutofdirtandsand. Evena
small amount of dirt will quickly dull a chain
and thus increase the possibility of kick-
back.
• Practice cutting a few small logs using the
following techniques to get the "feel" of us-
ing your saw before you begin a major
sawing operation.
• Squeeze the throttle trigger and allow
the engine to reach full speed before
cutting.
10