Scan Function; Saving Preferred Frequencies To; User-Defined Groups - Monacor International JTS UF-20S/5 Manual De Instrucciones

Receptor de banda ancha true diversity
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

3.5.3 Scan function

Before a transmission channel is selected, the
scan function can be used to determine if other
transmission systems are currently transmitting
on the channels of the receiver UF-20R / 5 or
UF-20S / 5 The channels already used will be
skipped during channel selection
Call up the selection menu for scanning via the
menu item
4. Scan
1. All Groups
2. Result List
3. Current Group
4. Return
It is possible to scan the channels of all groups
(
table starting on page 46) [this will take a
few minutes] or only the channels of one group
(this is faster)
– Scanning all channels –
1) Select the menu item 1
13) if it has not been selected yet Then press
the knob PUSH / CONTROL:
Scan All Groups
Press Setup or Enter to
start scan.
Press Exit to quit.
2) Press the button SETUP or the knob PUSH /
CONTROL to start scanning The display in-
dicates
Scanning...
time, press the button EXIT
3) After scanning, the result list appears showing
all free channels:
Scan Result List
G:
1
CH: 2
Open Channel : 16
Group 1 has been selected The lower line
indicates the number of free channels, in this
case 16 channels In group 1, 20 channels are
available, i e 4 channels are already being
used
4) All 15 groups can be selected when the knob
PUSH / CONTROL is turned
5) To select a free channel, press the knob so
that the channel number is highlighted Then
turn the knob When the knob is turned, the
channels already used are skipped
6) Press the button SETUP to save the channel
selected for reception
20
of the main menu:
Fig. 13
. All Groups
Fig. 14
To exit at any
%
Fig. 15
– Scanning the channels of a group –
1) If the selection menu for scanning (fig 13)
is not displayed, call it up via the menu item
4. Scan
2) Turn the knob PUSH / CONTROL to select the
menu item
the knob:
Scan Current Group
G:1
CH:1
3) Turn the knob PUSH /CONTROL to select the
group
4) Scanning of a group will always start with
the first channel which is automatically se-
lected To check the first channel, press the
knob PUSH /CONTROL After the check, the
display will show
if the channel is not already being used If the
channel is being used, it will be skipped and
(fig
the next free channel will be indicated
5) To check the next channel, press the knob
PUSH /CONTROL once again
6) Press the button SETUP to save the channel
for reception

3.5.4 Saving preferred frequencies to

user-defined groups

It is possible to save up to 64 preferred frequen-
cies to six user-defined groups
1) Call up the following submenu via the menu
item
3. User Group
1. Custom Groups
2. Clear Group
3. Return
2) The first menu item is selected Press the knob
PUSH /CONTROL to call up the following
setup menu:
Setup User Group
G:
U1
CH:1
---. --- MHz
3) The group number is selected Turn the knob
PUSH /CONTROL to select the group to
which the frequency is to be saved
4) Press the knob PUSH /CONTROL so that the
channel number is selected Turn the knob
to select the channel number to which the
frequency is to be saved
3. Current Group
Fig. 16
after the channel number
OK
of the main menu:
Fig. 17
Fig. 18
Then press

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jts uf-20r /5

Tabla de contenido