Kärcher HD 6/11-4 M Manual Del Usuario página 17

by this symbol are not allowed to be disposed of togeth-
er with the household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found
at: www.kaercher.com/REACH
Safety instructions
● It is essential that you read the safety instructions
5.951-949.0 before initial startup.
● Observe the national regulations for liquid jet clean-
ers.
● Observe the national accident prevention regula-
tions. Liquid jet cleaners must be tested regularly.
The test result must be recorded in writing.
● Do not modify the device or accessories.
Symbols on the device
The device may not be connected to the pub-
lic drinking water network.
The high-pressure jet must not be directed at
persons, animals, live electrical equipment or
at the device itself. Protect the device from
frost.
Safety devices
Safety devices protect the user and may not be disabled
or functionally circumvented.
The overflow valve, pressure switch an safety valve are
set and sealed by the manufacturer. Adjustments are
performed only by customer service.
Overflow valve with pressure switch
When the water quantity is reduced via the pressure/
quantity control on the trigger gun, the overflow valve
opens and part of the water flows back to the suction
side of the pump.
When the trigger on the high-pressure gun is release,
the pressure switch switches off the high-pressure
pump and the high-pressure jet stops.
The pump switches on again when the trigger is pulled.
Safety valve
The safety valve opens when the permissible operating
pressure is exceeded and the water flows back to the
suction side of the pump.
Control elements
See graphics page
Protector
1
Nozzle
2
Pressure and quantity regulation*
3
EASY!Lock spray lance
4
EASY!Force high-pressure gun
5
Safety latch
6
Trigger
7
Unlocking lever
8
EASY!Lock high-pressure hose
9
Push handle, top (pulled out)
10
Hose reel
11
Push handle, bottom (pushed in)
12
Rubber band
13
Cable clips, also a hose holder with the HD...M
14
Spray lance holder
15
Nozzle storage for rotary nozzle*
16
Power switch
17
Spray lance holder
18
EASY!Lock high-pressure connection
19
Sieve
20
Hose spout
21
Union nut
22
Water connection
23
Skid, stand
24
Holder for foam nozzle*
25
Transport retainer for surface cleaner*
26
Push handle lock
27
Crank
28
* not in the scope of delivery for all device variants
● Control elements for the cleaning process are yel-
low.
● Control elements for maintenance and servicing are
light grey.
1. Check the package content when unpacking.
2. Notify the dealer immediately in the case of shipping
damage.
3. Only with HD...M St: Store the drilling template on
the packaging for mounting the device on the wall.
Installing accessories
Note
No accessories are supplied in the scope of delivery for
the HD...M St.
Note
The EASY!Lock system connects components quickly
and safely via a single turn of the quick-release thread.
Figure A
1. Plug the high-pressure nozzle onto the spray lance.
2. Fit the union nut and hand-tighten (EASY!Lock).
3. Connect the spray lance to the high-pressure gun
and hand-tighten (EASY!Lock).
For devices without a hose reel:
1. Connect the high-pressure hose to the high-pres-
sure gun and high-pressure connection of the de-
vice and tighten hand-tight (EASY!Lock).
For devices with a hose reel:
1. Lay the high-pressure hose on the ground in a
straight line.
2. Turn the crank clockwise and wind the high-pres-
sure hose onto the hose reel in evenly distributed
layers. Take care to ensure that the hose does not
become kinked.
3. Connect the high-pressure hose to the high-pres-
sure gun and hand-tighten (EASY!Lock).
English
Colour coding
Unpacking
17