Bosch HEAVY DUTY GHO 18V-LI Professional Manual Original página 15

(20) Scale for rebate width a)
(21) Locking nut for rebate width setting
(22) Fastening screw for parallel/angle guide
(23) Angle guide a)
(24) Locking nut for angle adjustment
(25) Fastening screw for rebate depth guide
(26) Rebate depth guide a)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Planer
Article number
Rated voltage
No-load speed
A)
Cutting depth
Rebate depth
Max. planing width
Weight according to EPTA-Pro-
cedure 01:2014 B)
Recommended ambient tem-
perature during charging
Permitted ambient temperature
during operation C) and during
storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20−25 °C with rechargeable battery ProCORE18V
12.0Ah.
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Noise/vibration information
Noise emission values determined according to
EN 62841-2-14.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 85 dB(A); sound power level
96 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-14
a <2.5 m/s 2 , K = 1.5 m/s 2 .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
Bosch Power Tools
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
a)
power tool is used for other applications, with different ap-
a)
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
a)
working period.
a)
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
GHO 18V-LI
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
3 601 EA0 3..
V 18
Fitting
min 14,000
-1
mm 0–1.6
u
mm 0–8
mm 82
kg 2.3–3.4
Battery charging (see figure A)
°C 0 to +35
u
°C –20 to +50
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
GBA 18V...
before using your power tool for the first time.
ProCORE18V...
The lithium-ion battery can be charged at any time without
GAL 18...
reducing its service life. Interrupting the charging process
GAX 18...
does not damage the battery.
GAL 36...
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
To remove the battery (7), press the release button (8) and
pull the battery downwards out of the power tool. Do not
use force to do this.
The hex key (12) required for changing the planer blade is
housed inside the power tool and should always be stored
there (see figure A).
Follow the instructions on correct disposal.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 7T9 | (17.05.2022)
English | 15
to