Leica CINE 1 Instrucciones Abreviadas página 5

NETWORK UND MAINS CABLE
• The device must not be touched with wet hands.
• Mains cables must be routed in such a way as to protect them from kinking,
sharp edges, chemicals and sources of high heat. Do not place heavy ob-
jects on top of the mains cable. A damaged mains cable poses a hazard of
electrocution and a fire hazard.
• Pull the mains plug on the plug body only. Never pull it by the cable.
• The device must not be moved as long as it is connected to a power socket.
• Use only the mains cable provided for this device. A damaged or loose
mains cable or a damaged power socket must not be used.
• Any connected aerial cables and the mains cable must be unplugged during
a lightning storm. An electrical overload due to lightning strike can damage
the device via the aerial cable and the mains cable.
VENTILATION AND HIGH TEMPERATURES
20 cm / 8 in
• The device must always be well ventilated. A space of at least 20 cm / 8 in
on both sides and of 15 cm / 6 in on the back of the device must always be
maintained to ensure optimal air circulation.
• Excessive heat and insufficient ventilation can result in the premature fail-
ure of some electric components and may pose a fire hazard.
• The air vents must be unobstructed at all times.
• Do not touch the device while it is running or just after it has been switched
off, as it can be very hot.
• Do not insert any foreign objects into the air vents!
REMOTE CONTROL BATTERIES
• Only the battery type stated and described in this manual must be used.
Any improper use of the batteries or the use of unapproved battery types
may result in an explosion!
• Incorrectly inserted batteries can leak, corrode, or explode.
• Batteries must only ever be replaced with the same battery type. Do not
mix depleted with fresh batteries or with different battery types.
• Do not expose the batteries to direct sunlight, heat, humidity or moisture
for prolonged periods of time. They must not be placed in a microwave oven
or a high-pressure container as this would pose a fire or explosion hazard!
• Never dispose of batteries in fire and never attempt to heat, recharge, dis-
mantle or break open a battery.
• Applicable disposal regulations must be complied with.
• Depleted batteries must never be disposed of in household waste as they
contain toxic materials that are harmful to the environment.
• Remove the batteries from the housing if you will not be using the product
for an extended period of time. In case of battery leakage, the battery com-
partment must be wiped clean with a cloth.
• Please do not use alkaline batteries, standard (carbon zinc) batteries or
rechargeable (NiCd, NiMH, etc.) batteries.
• Batteries must always be stored out of the reach of children. Batteries must
never be left lying around unattended, as they could be swallowed by chil-
dren or pets. Batteries can cause suffocation when swallowed. A swallowed
battery can additionally cause severe internal injuries or death.
FIRST AID
• Battery fluid may cause blindness if it comes into contact with the eyes.
Rinse the eyes thoroughly with clean water immediately. Avoid rubbing.
Seek medical attention immediately.
• Leaked battery fluid poses an injury hazard when it comes in contact with
clothing or skin. Rinse the affected areas thoroughly with clean water.
GROUNDING OF THE HOUSE AERIAL
• Where a house aerial is to be used, the aerial system must be appropriately
protected against overvoltage and static discharge.
15 cm / 6 in
20 cm / 8 in
VOLUME
• Loud music and noise can cause irreparable damage to hearing. Extreme
volumes should be avoided, especially during long-term exposure and when
using headphones.
• Reduce the volume immediately or avoid using headphones for a while if
you experience tinnitus or pain.
WARNINGS REGARDING THIS LASER PRODUCT
Attention
• This device comes with a laser module. Do not disassemble or modify
the device in any way. Doing so may pose injury hazards. Emitting laser
radiation may pose a serious health risk.
• Never look directly into the lens while the device is operational. Never
look directly into the emitted light beam! Doing so may cause severe
damage to your eyes or permanent blindness!
• RG2: Never look directly into the emitted light beam!
IEC 62471-5: 2015
CLASS 1 Laser PRODUCT IEC 60825-1: 2014
λ = 459–471 nm/519–531 nm/635–651 nm
• Any operation not described in this manual or any alterations made to
the device may result in hazardous radiation exposure.
• The Device Complies with 21 CFR 1040.10 and 1040.11 except for con-
fromance as a Risk Group 2 LIP as defined in IEC 62471-5: Ed.1.0. For
more information see Laser Notice No.57, dated May 8, 2019.
• Eye protection with an optical density of 4 or more (wavelength 459-
651 nm) must be worn if this unit requires repair.
GENERAL INFORMATION
• New products and materials may release chemicals into the air through
evaporation. For the initial first few hours of operation, the device can
therefore generate some odor. This is caused by some of the device com-
ponents heating up for the first time. All materials used fully comply with
environmental requirements and regulations. The vapors responsible for the
odor will diminish over time. We recommend running the machine in a well
ventilated environment for some time before its actual initial use.
• All data, including personal information, may be changed or deleted due to
incorrect or accidental operation, static discharge, accidents, malfunctions,
repairs and other actions. Leica Camera AG does not accept liability for
direct or consequential damage due to the manipulation or destruction of
data and personal information.
CARE AND STORAGE
• Do not touch the device while it is running or just after it has been switched
off, as it can be very hot.
• Do not wipe down the device with oil, as it could corrode surfaces or dam-
age the coating.
• Prolonged direct contact with rubber or ethylene products can contaminate
this device.
• The lens must not be touched directly or wiped with a cleaning cloth. Use
a dust blower to remove dust from the lens. Grease, dirt and fingerprints
must be carefully cleaned off by a professional using an optical cleaning
cloth, lens paper, or professional cleaning solutions. Otherwise the optical
film on the lens can be destroyed and result in a negative impact on the
image quality.
• The device must always be switched off and the mains cable must be dis-
connected before cleaning.
• The device and the remote control should always be cleaned using a soft,
moist, clean, naturally dyed cloth. Please do not use any chemicals.
• The surfaces or glass components of the device can be damaged or even
destroyed if the device is exposed to insect repellents, solvents, or other
volatile substances.
• During cleaning, no water or other liquids must be sprayed or poured direct-
ly onto the device. Doing so would cause severe damage.