Publicidad
Idiomas disponibles
Idiomas disponibles
Start up Instructions
Congratulations! You have completed the
installation of your new water filtration system.
Please Follow the Startup Instructions.
Step 1
- Turn on water supply.
Step 2
- Flush new cartridge with 5 gallons of water prior to
use and check for leaks. A container with a known
volume can be filled to determine how much water
has flushed through the system. If leaks occur,
check tightness of tubing and fittings. If leaks persist,
discontinue use and call Retail customer service.
NOTICE
Check frequently over the next 24 hours to ensure no leaks
are present
Product Registration
To Register your product, please visit www.watts.com/pureh2o
and select "Register Now". Watts is concerned for the safety of
your personal information. WATTS collects personal information
when you register with Watts. This information is stored in our
data base and we do not rent, sell, or share personal information
with other people or nonaffiliated companies. We will send you
certain types of communications such as direct mail, email, or
by telephone relating to our products or products that you have
purchased only with your prior permission. We limit access to
your personal information to those employees who will directly
provide you with services or products in order to do their jobs.
See our privacy policy at - http://www.watts.com/privacy.asp
See Terms of Use at - http://www.watts.com/terms.asp
Changing the Filter Cartridges
6 Month System Maintenance
Replace:
Inline Granular Activated Carbon filter with Quick
connect fitting H2O-FK102 (88005227)
To buy replacement part(s) please visit the retail store or their
website or contact Watts retail customer service at
(888) 321-0500
Step 1:
Turn off the incoming water supply.
Step 2:
Follow instructions in section 'Filter and Quick connect
fitting installation'
Step 3:
After installation follow startup steps.
Performance Data Sheet
Pure H2O
-In U.S.-Watts Regulator Co., N. Andover, MA 01845
(Watts.com)
-In Canada-Watts, Water Technologies (Canada), Inc. Toronto,
ON M5J3G6 (Watts.ca)
Inline Granular Activated Carbon Filter with Quick-
Connect Fittings: H2O-FK102
GENERAL USE CONDITIONS
WARNING
!
1: System to be used with municipal or well water sources
treated and tested on regular basis to insure bacteriological safe
quality. DO NOT use with water that is micro biologically unsafe
or of unknown quality without adequate disinfection before or
after the system. While testing was performed under standard
laboratory conditions, actual performance may vary.
2: Operating Temperature: Maximum 100° F (38° C)
Minimum 35° F (2° C)
3: Operating Water Pressure: Maximum 100-psi (690 kpa)
Minimum 25-psi (172 kpa)
4: Flow Rate: 0.5 gpm (3.8 Lpm)
5: Change time interval: 2500 Gallons (9,464 Liters) or after 6
months
This system has been tested according to NSF/ANSI Standard
42 for the reduction of the substances listed below.
The concentration of the indicated substances in water entering
the system was reduced to a concentration less than or
equal to the permissible limit for water leaving the system, as
specified in NSF/ANSI 42. Testing performed under standard
laboratory conditions, actual performance may vary.
This system is certified to NSF/ANSI standard 372 for 'lead free'
compliance.
Description
Percent
Reduction
CHLORINE
97.4%
TASTE &
ODOR
This system is assembled at Watts Facility- Avenida Obregon 4055 Parque
Industrial El Cid, Nogales, 84092 Mexico
Page 3
Influent Challenge
Maximum Permissible
Concentration
Product Water
(mg/L unless noted)
Concentration
2.0 mg/L + 10%
> = 50%
Publicidad
