DeWalt DCW600 Manual De Instrucciones página 17


WARNING: Always follow the bit manufacturer's
speed recommendations as some bit designs
require specific speeds for safety or performance.
If you are unsure of the proper speed or are
experiencing any type of problem, contact the
bit manufacturer.
This router is equipped with a variable speed dial
7 speeds between 16000 and 25500 RPM. Adjust the speed
by turning the variable speed dial
NOTICE: The router is equipped with electronics
to monitor and maintain the speed of the tool
while cutting. In low and medium speed operation,
the speed control prevents the motor speed from
decreasing. If you expect to hear a speed change and
continue to load the motor, you could damage the
motor by overheating. Reduce the depth of cut and/or
slow the feed rate to prevent tool damage.
The compact routers are equipped with electronics to
monitor and maintain the speed of the tool while cutting.
sPEED sElECTiOn ChART*
DIAL SETTING APPROX. RPM
1 16000
2 17500
3 19100
4 20700
5 22300
6 23900
7 25500
*The speeds in this chart are approximate and are for reference only. Your
router may not exactly produce the speed listed for the dial setting.
nOTE: Make several light passes instead of one heavy pass
for better quality work.
Worklights (Fig. A)
The worklights are located at the front of the
10
motor . To turn on the worklight, switch on the on/off
6
switch 3 . Worklights will remain on 20 seconds after the
on/off switch is moved to the off position.
nOTE: The worklights are for lighting the immediate work
surface and are not intended to be used as a flashlight.
nOTE: If worklights flash, check the charge on the battery;
it could be low. If they still flash with a charged battery, the
unit should be taken to a service center for evaluation.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
4 with
.
4
APPLICATION
Large diameter bits and cutters
Small diameter bits and cutters.
Softwoods, plastics, laminates.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a dry cloth. Never let
any liquid get inside the tool; never immerse any part
of the tool into a liquid.
nOTE FOR PlUngE BAsE OnlY: Use only a DRY cloth to
wipe the plunge rods. These rods require no lubrication.
Lubricants attract dust, reducing the performance of
your tool.
Waxing Motor and Base
To maintain a smooth action when moving the motor unit
in relation to the base, the outside of the motor unit and the
inside of the base can be waxed using any standard paste or
liquid wax. Per the manufacturers instructions, rub the wax
onto the outside diameter of the motor unit and the inside
diameter of the base. Allow wax to dry and buff off residue
with a soft cloth.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
English
WALT
e
WALT Industrial
e
WALT factory
e
15