Atlas Copco LZB33-LB-AR005-11 ATEX Manual De Instrucciones página 8

Safety Information
• 40°C is also the maximum allowed temperature of the
compressed air when it enters the product.
• If the product is installed in an equipment, the entire
equipment has to correspond to the guidelines 2014/34/
EU.
• Make sure that the compressed air fulfil our quality de-
mands (quality classes 2.4.3. and 3.4.4 respectively 3.5.4
acc. to ISO/DIS 8573-1:2010).
• Do not exceed maximum pressure of 6.3 bar, or as stated
on the product nameplate. Exceeding the operating pres-
sure can increase the surface temperature due to higher
rotating speed and the product can become an ignition
source.
Ex Classification
If the product is part of an assembly where the components
have different Ex classification, the component with the low-
est level of safety defines the Ex classification of the com-
plete assembly.
Explosion Prevention Guidelines
Cleanliness
• Make sure the product is kept clean from dust and dirt to
prevent increased bearing and surface temperature.
• If using a silencer: Make sure a silencer with a filtering
effect at the air outlet is installed to prevent any friction-
heated particles entering into the surrounding atmos-
phere.
Usage
• Make sure the product is earthed to the equipotential
bonding system of the workshop, for example through
accessories such as hoses and air-pressure connections.
• It is the responsibility of the user to make sure that the
product and all possible accessories, such as wrenches
and air connections, conform to the national safety regu-
lations for equipment used in potentially explosive areas.
Useful Information
Website
Information concerning our Products, Accessories, Spare
Parts and Published Matters can be found on the Atlas Copco
website.
Please visit: www.atlascopco.com.
ServAid
ServAid is a portal that is continuously updated and contains
Technical Information, such as:
• Regulatory and Safety Information
• Technical Data
• Installation, Operation and Service Instructions
• Spare Parts Lists
8 © Atlas Copco Industrial Technique AB - 9836 7279 00
LZB33-LB-AR005-11 ATEX
• Accessories
• Dimensional Drawings
Please visit: https://servaid.atlascopco.com.
For further Technical Information, please contact your local
Atlas Copco representative.
Caractéristiques techniques
Indice IP
L'indice IP des moteurs pneumatiques se réfère au carter mé-
canique conformément à la norme IEC 60529. L'indice IP ne
couvre pas la résistance à la corrosion ou à d'autres liquides
autres que de l'eau douce potable.
Caractéristiques techniques
Référence
Modèle
Consommation d'air à la
vitesse à vide
Consommation d'air à la
vitesse à vide
Consommation d'air à la puis-
sance maxi.
Consommation d'air à la puis-
sance maxi.
Couple de freinage
Couple de freinage
Frein intégré
Matériau des pièces externes Hardened steel/Aluminium
Vitesse à vide
Puissance maxi.
Puissance maxi.
Couple de démarrage mini.
Couple de démarrage mini.
Rapport
Sens de rotation
Code de chargement de l'ar-
bre
Type d'arbre
Vitesse à la puissance maxi.
Couple de calage
Couple de calage
Couple à la puissance maxi.
Couple à la puissance maxi.
Type de palettes
Poids
Poids
Flexible d'alimentation
Flexible d'alimentation
Indice de protection
Flexible de sortie
Flexible de sortie
8411034054
LZB33-LB-AR005-11
l/s
cfm
7.9 l/s
16.8 cfm
16 Nm
12 ft lb
Yes
450 tr/min
0.25 kW
0.34 hp
12.6 Nm
9.3 ft lb
Reversible
c
Keyed
240 tr/min
19.6 Nm
14.5 ft lb
9.8 Nm
7.2 ft lb
Lubrication free
1.63 kg
3.59 livres
10 mm
0.4 pouces
IP66
10 mm
0.4 pouces