Hudson Back Reliever 62192 Instrucciones

FOR YOUR SAFETY
This sprayer operates with liquid under pressure.
Failure to observe CAUTIONS and follow instructions
for use and maintenance can cause tank, hose or
other parts to become corroded, weakened, and/or
burst. This can result in SERIOUS INJURY or PROPERTY
DAMAGE from forcible ejection of parts or high-
pressure discharge of spray material.
DO NOT USE ANY FLAMMABLES OR BOILING LIQUIDS
IN THIS SPRAYER as it is not designed nor intended
for such use. Some spray materials can ignite or
explode. Do not spray in an enclosed space, near
an open flame such as found in a BBQ grill or water
heater, near an electric motor or open switch, or
any source of heat. DO NOT SMOKE while spraying.
Use of flammables could result in SERIOUS INJURY
or PROPERTY DAMAGE from unintended ignition or
explosion. DO NOT USE ANY CAUSTICS OR ACIDS IN
THIS SPRAYER, since these can damage or weaken
the sprayer and its parts, resulting in SERIOUS INJURY
or PROPERTY DAMAGE. Keep out of reach from
children and pets. Always read and follow directions
on the spray material container.
LIMITED WARRANTY
H. D. Hudson Manufacturing Company warrants
to the original consumer purchaser of this product
at retail that it is free from defects in materials and
workmanship for the period of 3 years from the
original date of purchase. This warranty does not
apply to damage to the product resulting from
accident, misuse, neglect, alteration, modification,
tampering, or failure to follow instructions supplied
with the product. This warranty does not cover
normal wear and tear of O-Rings or seals, and
the warranty shall be void if the product is used
commercially. If the product or any part of it should
malfunction within the warranty period, call
1-800-977-7293. Valid only in North America.
H. D. Hudson Manufacturing Company
500 N. Michigan Avenue • Chicago, IL 60611
Phone: (800) 977-7293 Fax: (312) 644-7989
Web: www.hdhudson.com
www.facebook.com/hudsonsprayers
www.youtube.com/hudsonsprayer
Replacement Part Kit: #6985
62192 Back Reliever™ Polyethylene Sprayer Instructions
If you have any questions or concerns, or missing parts,
Do not return sprayer to the store!
1-800-9-SPRAYER
Call our hotline: (1-800-977-7293)
Common maintenance questions:
www.hdhudson.com/FAQS
INSIDE THE BOX
• Sprayer Tank • Shut-off Valve
• Pump • Supply Tube
• Spray Wand • Instructions
• Hose
HOW TO ASSEMBLE
Poly Tank Assembly Video
View Online
@ hdhudson.com
1. Assemble hose.
a.) Side to tank: Slide large hose cap nut onto
hose, threads face end of hose. Insert hose barb
to end of hose. Insert supply tube into hose barb.
b.) Side to shut-off valve: Slide small shut-off valve
onto hose, threads face end of hose. Insert barb
end of shut-off valve onto hose. IMPORTANT: Be
sure hose is all the way over the barb! Tighten
shut-off valve cap nut to shut-off valve.
2. Insert the supply tube into the tank and securely
thread on the cap nut. CAUTION: Make sure the
cap nut is threaded all the way down. If loose,
it may come off with force or spray may escape
resulting in SERIOUS INJURY.
3. Attach spray wand to shut-off valve.
• Insert spray wand fitting into shut-off valve.
• Screw down wand retainer cap nut onto valve.
Screw nut onto the shut-off valve. Note: This
is not a compression fitting, but it is normal for
nut to screw on tightly.
1 .
a
3.
1 .
b
2.
See maintenance and instructional
videos on the internet:
www.hdhudson.com/instructional-videos
HOW TO FILL
A.) Pour measured amount of spray material into
the open tank. Follow label directions on
spray material container for amount to use.
B.) Add water as directed.
Do not fill beyond the MAX FILL line.
C.) Insert pump and turn clockwise to seal.
Do not over tighten.
A
B
HOW TO PRESSURIZE
Unlock pump handle by pushing down and
turning handle. Do not unscrew pump cap or
remove pump. Using the handle, pump up and
down. The more you pump, the more pressure
you will build up inside the tank. When it
becomes difficult to pump, your tank has
reached maximum pressure. Do not stand so
your head is over pump.
• Use low pressure (fewer strokes) for a
coarse spray.
• Use high pressure (more strokes) for a fine
mist or a long-reaching stream.
871-232 Instruction
HOW TO SPRAY
Squeeze handle to spray
Release handle to stop
Push handle forward to lock.
Push handle back to unlock.
Note: Spray may stop
if nozzle is tightened
all the way down.
Tighten nozzle for fine mist
Loosen nozzle for coarse or long range
HOW TO RELEASE PRESSURE
Turn sprayer on its side and turn nozzle away from you.
Squeeze lever or push button to "ON" and let all the air
C
escape. Turn sprayer up-right and slowly unscrew pump
from tank and remove it. Do not stand so your head
is over pump. This sprayer is equipped with a pressure
release valve on the tank, you may also twist the top
portion open and hold it until all air has escaped. Twist
valve closed to reseal. Then remove pump.
SERVICE AND MAINTENANCE
Visit www.hdhudson.com/FAQS
Clean and dry your sprayer after every use to greatly
prolong its useful service life. Many spray materials will
harden if left in the sprayer and plug up the nozzle,
shut-off valve or supply tube. The soft parts, O-rings and
gaskets, will ultimately wear out and need replacing, just
like the oil filter on your car, for example. How often they
need replacing depends on how much you spray, the
spray materials you use and whether or not the sprayer is
regularly cleaned after use. Call 1-800-9-SPRAYER or visit
hdhudson.com to obtain genuine Hudson replacement
parts. If you leave your sprayer in the garage over Winter,
particularly in northern areas, the soft parts may dry out
and need servicing before you use your sprayer for the
first time in the Spring.
©2012 H. D. Hudson Manufacturing Company