Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Radio housing • B) Radio brackets • C) Switch panel cover • D) Ribbon cable • E) Panel clips • F) Phillips screws (8)
A
B
Metra. The World's Best Kits.
®
BMW 1 Series
2008-2013
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DDIN radio provision
• Painted scratch resistant matte black to match the factory finish
C
D
F
MetraOnline.com
(without NAV, with automatic climate control)
E
© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
95-9327B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . ..............................................2-3
Kit Preparation . ......................................................4
Kit Assembly ..........................................................5
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Please visit metraonline.com
for wiring harness options
Antenna Adapter: 40-EU10
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Cutting tool
Attention!
With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
REV. 2/9/23 INST95-9327B
Publicidad
Manuales relacionados para Metra 95-9327B
Resumen de contenidos para Metra 95-9327B
- Página 1 Ensure that all installation connections are secure before cycling the ignition to test this product. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 2/9/23 INST95-9327B...
- Página 2 DASH DISASSEMBLY 1. Unclip and remove the dash trim panel above the radio and glove box. (Figure A) 2. Unclip the climate control panel then unplug and remove. (Figure B) Continued on the next page (Figure B) (Figure A) 386.257.1187 MetraOnline.com...
- Página 3 DASH DISASSEMBLY (CONT.) 3. Remove (2) screws securing the bottom of the radio, then unplug and remove the radio. (Figure C) 4. Unclip the climate controls from the climate control panel and save for reassembly. (Figure D) 5. Unclip and remove the switch panel below the climate controls (if equipped) (Figure E). (Figure C) (Figure D) (Figure E) Continue to Kit Preparation REV. 2/9/2023 INST95-9327B...
- Página 4 KIT PREPARATION 1. Using a cutting tool, remove the sections 4. Attach the White connector from the of sub-dash indicated to provide ribbon cable supplied with the kit to the clearance for the radio and climate circuit board. controls. (Figure A) 5. Reinstall the circuit board back into the Remove shaded areas 2. Install the (2) panel clips to the switch panel. radio housing. 6. Clip the climate control panel, and switch panel, into the radio housing. (Figure C) For models with a switch panel below the climate control. 7. Attach the Black connector from the ribbon cable to the climate control 2. Remove (5) screws securing the switch (Figure A) (Figure C) panel. (Figure D)
- Página 5 KIT ASSEMBLY ISO DDIN radio provision 1. Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A) Note: Radio mounting screws must be flush with the mounting brackets. Countersunk flat-head screws have been provided if needed. (Figure A) 2. Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation. 3. Secure the completed assembly into the (Figure A) dash with the factory screws. 4. Reassemble the dash in reverse order of disassembly using radio trim panel assembly to complete the installation. REV. 2/9/2023 INST95-9327B...
- Página 6 386.257.1187 MetraOnline.com...
- Página 7 REV. 2/9/2023 INST95-9327B...
- Página 8 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 2/9/23 INST95-9327B...
- Página 9 Asegúrese de que todas las conexiones de la instalación estén seguras antes de encender y apagar el encendido para probar este producto. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 2/9/23 INST95-9327B...
- Página 10 DESMONTAJE DEL TABLERO 1. Desenganche el panel de moldura del tablero que están del radio y la guantera y quítelo. (Figura A) 2. Desenganche el panel de control de clima y después, desconéctelo y quítelo. (Figura B) Continúa en la siguiente página (Figura B) (Figura A) 386.257.1187 MetraOnline.com...
- Página 11 DESMONTAJE DEL TABLERO (CONT.) 3. Quite (2) tornillos que fijan la parte inferior del radio. Después, desconecte el radio y quítelo. (Figura C) 4. Desenganche los controles de clima del panel de control de clima y consérvelos para cuando deba rearmarlo. (Figura D) 5.
- Página 12 PREPARACIÓN DEL KIT 1. Use la herramienta de corte para quitar 4. Fije el conector blanco del cable plano de las secciones del subtablero indicadas transmisión incluido con el kit al tablero para que haya espacio suficiente para el de circuitos. radio y los controles de clima.
- Página 13 (Figura A) 2. Localice el arnés de cableado de fábrica y el conector en el tablero y realice todas las conexiones necesarias al radio. Metra recomienda el uso de adaptadores de acoplamiento adecuados de Metra o de Axxess. Pruebe el radio para asegurarse de que funciona bien.
- Página 14 386.257.1187 MetraOnline.com...
- Página 15 REV. 2/9/2023 INST95-9327B...
- Página 16 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recomienda MECP técnicos certificados Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 2/9/23 INST95-9327B...