Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING:
!
The tool may fire when it is first
connected to the air source. Always
connect the tool to the air source before
loading fasteners to prevent injury from
unintended cycling. Always make sure
the tool's magazine is empty at the
beginning of each work session, before
connecting to an air source.
WARNING:
!
Use only those fasteners recommended
for use with this tool. Fasteners not
identified for use with this tool by the tool
manufacturer are able to result in a risk of
injury to persons or tool damage when
used in this tool.
WARNING:
!
Keep the tool pointed away from yourself
and others when loading fasteners.
Failure to do so could result in possible
serious personal injury.
WARNING:
!
Never load fasteners with the workpiece
contact or trigger activated. Doing so
could result in possible serious personal
injury.
UNLOADING FASTENERS
Unloading is the reverse of loading. Always
disconnect the air source before unloading.
WARNING:
!
Always unload all fasteners before removing
tool from service.
WARNING:
!
Always disconnect the air source before
unloading.
CLEARING JAMS
Occasionally, a fastener may become jammed in
the firing mechanism of the tool, making the tool
inoperable. To remove a jammed fastener, follow
the steps below:
08
Disconnect the tool from air source.
⒈
Remove fasteners from the tool. Failure to do so
⒉
will cause the fasteners to eject from the front of
the tool.
⒊
Pull up on the latch (D) and open the jam release
(E).
⒋
Using caution not to bend or damage the driver
blade, using pliers or a screwdriver if required to
clear the jammed fastener.
⒌
Close the jam release and latch.
⒍
Reconnect the tool to the air source.
⒎
Reload the tool with fasteners.
Latch (D)
Jam release ( ) E
WARNING:
!
Make sure there is no fastener in
magazine before clearing a jam.
WARNING:
!
Disconnect the tool from the air source
whenever clearing a jam. After
disconnecting the tool from the air
compressor, there should still be enough
air pressure to fire the tool. After the air
hose is disconnected, always fire the tool
into scrap wood repeatedly to make sure
all of the compressed air is expended.
NON-MARRING PAD
The no-marring pad attached the nose of the tool
helps prevent marring and denting when working
with softer woods.
WARNING:
!
Disconnect the tool from the air source
before removing or replacing the no-
marring pad. Failure to do so could result
in serious personal injury.
To remove the pad
: Pull the no mar tip towards the
back of the tool following the
work contact element
To replace the pad
: Push the no mar tip on to the
tool inserting the opening of the no mar tip on to the
work contact element tip.
SETTING THE AIR PRESSURE
The amount of air pressure required depends on
the size of the fasteners and the workpiece material.
Begin testing the depth of drive by driving a test nail
into the same type of workpiece material used for
the actual job. Drive a test fastener with the air
pressure set at 90-95psi. Raise or lower the air
pressure to find the lowest setting that will perform
the job with consistent results. It may be possible to
achieve the desired depth with air pressure
adjustments alone.
DEPTH ADJUSTMENT
The driving depth of the fasteners are adjustable.
To adjust the depth, use the drive depth adjustment
wheel (F) on the right side of the tool.
1.
Disconnect the tool from air source.
2.
Turn the depth wheel left or right to change the
driving depth.
3.
Reconnect the tool to the air source.
Drive a test nail after each adjustment until the
4.
desired depth is set.
Adjustment
wheel(F)
Flush
Too Deep
Turn the adjustment knob count clockwise
Adjustment
.
wheel(F)
Too Shallow
Turn the adjustment knob clockwise
CAUTION:
It is advisable to test the depth on a scrap
workpiece to determine the required
depth for the application.
To determine depth of drive, first adjust
the air pressure and drive a test fastener.
Never exceed 120psi.
FIRING THE TOOL
The tool is equipped with a trigger that select one of
two firing modes.
SEQUENTIAL FIRING MODE
Single sequential actuation provides the most
accurate fastener placement.
To use the tool to drive nails in this actation mode,
WCE and trigger must be used in a specific order.
1.
Disconnect tools from the air source.
2.
Press
the selectable firing mode button,
the selectable firing mode switch in the upwards,
the firing mode indicator should be pointing at the
single nail icon.
3.
C
onnect tools to the air source.
. 4
The work contact element(WCE) must be
completely depressed by placing the nose of the
tool against the work piece.
5.
The trigger must be pulled firmly and then
released.
6.
The tool must be allowed to recoil away from the
work piece.
To continue operation in a separate location, move
the tool along the work peiece, repeating step 4
through 6.
Flush
turning
09
Publicidad
