Publicidad
Idiomas disponibles
Idiomas disponibles
CLEANING
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from
various types of commercial solvents and maybe
damaged by their use. Use clean cloths to remove
dirt, dust, oil, grease, etc.
WARNING:
!
Do not at any time let brake fluids,
gasoline, petroleum-based products,
penetration oils, ect., come in contact
with plastic parts. Chemicals can damage,
weaken or destroy plastic which may
result in serious personal injury.
COLD WEATHER OPERATION
For cold weather operation, near and below freezing,
the moisture in the air line may freeze and prevent
tool operation. We recommend the use of air tool
lubricant or permanent antifreeze (ethylene glycol)
as a cold weather lubricant.
CAUTION:
Do not store tools in a cold weather
environment to prevent frost or ice
formation on the tool's operating valves
and mechanisms that could cause tool
failure.
Quick
Coupler
Air hose
Quick
connector
12
RECOMMENDED HOOKUP
The air compressor must be able to maintain a
1.
minimum of 60psi when the tool is being used.
An inadequate air supply can cause a loss of
power and inconsistent driving.
2.
An oiler can be used to provide oil circulation
through the tool. A filter can be used to remove
liquid and solid impurities which can rust or gum
up internal parts of the tool.
3.
Always use air supply hoses with a minimum
working pressure rating equal to or greater than
the pressure from the power source if a regulator
fails, or 150psi, whichever is greater. Use 3/8" air
hose for runs up to 50'. Use 1/2" air hoses for 50'
run or longer. For better performance, install a
3/8" quick plug(1/4" NPT thread) with an inside
diameter of 0.315" (8mm) on the tool and 3/8"
quick coupler on the air hose.
Use a pressure regulator on the compressor,
⒋
with an operating pressure of 0-125psi. A
pressure regulator is required to control the
operating pressure of the tool between 60psi and
100psi.
CAUTION:
The air compressor must be able to
maintain a minimum of 60psi when the
tool is being used. An inadequate air
supply can cause a loss of power and
inconsistent driving.
WARNING:
!
Do not connect with an air compressor
which can potentially exceed 200psi. As
tool may burst, possibly causing injury.
Quick
Filter
Oiler
connector
Compressor
Quick
Regulator
Coupler
TROUBLESHOOTING
WARNING:
!
Stop using tool immediately if any of the following problems occur. Serious personal injury
could result. Any repairs or replacements must be done by a qualified service person or an
authorized service center.
PROBLEMS
POSSIBLE CAUSE(S)
O-rings in trigger valve housing are
Air leaking at trigger
damaged
valve area.
Air leaking between
Loose screws in housing
housing And nose.
1.Damaged O-rings
2.Damaged to bumper
Air leaking between
1.Loose screws
housing and Cap.
2.Damaged gasket
Tool skips driving
1.Worn bumper
fastener
2.Dirt in nose piece
3.Dirt or damage prevent fasteners or
pusher from moving freely in
magazine
4.Damaged pusher spring
5.Inadequate air flow to tool
6.Worn O-ring on piston or lack
of lubrication
7.Damaged O-ring on trigger valve
8.Air leaks
9.Cap seal leaking
Tool runs slow or has
1.Tool not lubricated sufficiently
loss of power
2.Broken spring in cylinder cap
3.Exhaust port in cap is blocked
Fasteners are jammed
1.Guide on driver is worn
in tool
2.Fasteners are not correct size
3.Fasteners are bent
4.Magazine or nose screws are loose
5.Driver is damaged
CORRECTIVE ACTION
Replace o-rings. Check operation
of Work Contact Element(WCE)
Tighten screws
1.Replace o-rings
2.Replace bumper
1.Tighten screws
2.Replace gasket
1.Replace bumper
2.Clean drive channel
3.Clean magazine
4.Replace spring
5.Check fitting, hose, or compressor
6.Replace and lubricate o-rings
7.Replace o-rings
8.Tighten screws and fittings
9.Replace gasket
1.Lubricate nailer
2.Replace spring
3.Replace damaged internal parts
1.Replace guide
2.Use only recommended fasteners
3.Replace with undamaged fasteners
4.Tighten screws
5.Replace driver
13
Publicidad
