Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
SOLID STAINLESS
STEEL SHELVING
TOOL NEEDED
Rubber Mallet
SHELF PARTS
Shelf x 4
NOTE: Two-shelf wire shelving units include
two shelves and eight sets of shelf supports.
Figure 1
Figure 2
Figure 3
PAGE 1 OF 6
1-800-295-5510
uline.com
Shelf Support x 16 Sets
SELF-LEVELING FEET OR CASTER INSTALLATION
SELF-LEVELING FEET
NOTE: If installing casters, do not install self-leveling feet.
1.
Ensure post is positioned as shown. (See Figure 1)
2. Insert self-leveling foot into open end of post.
3. Use a rubber mallet/hammer or tap on ground until self-leveling foot slides
into post.
4. Repeat steps 2 and 3 for remaining posts.
CASTERS (ULINE MODEL # H-1205WH SOLD SEPARATELY)
1.
Ensure post is positioned as shown. (See Figure 2)
2. Engage the wheel brakes to keep casters from rolling during assembly.
Use a rubber mallet to tap caster stems into posts. (See Figure 2)
1.
Start with the lowest shelf. Snap the interlocking pieces of a
shelf support (wide end down) around the post at the lowest
groove where shelf is to be located. Slide the support up or
down until it snaps onto the groove. Add a shelf support to the
same place on the remaining posts. (See Figure 3)
NOTE: NSF requires food service applications to keep the
lowest shelf at least 6" above the floor.
Post x 4
NOTE: Self-leveling feet are located within
post carton.
ASSEMBLY
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
POST PARTS
Self-Leveling Foot x 4
0423 IH-5466
Publicidad
Manuales relacionados para Uline IH-5466
Resumen de contenidos para Uline IH-5466
- Página 1 3. Use a rubber mallet/hammer or tap on ground until self-leveling foot slides into post. 4. Repeat steps 2 and 3 for remaining posts. CASTERS (ULINE MODEL # H-1205WH SOLD SEPARATELY) Ensure post is positioned as shown. (See Figure 2) Figure 2 2.
- Página 2 3. Stand unit upright. Gently tap shelf down to secure it. (See Figure 5) Figure 5 4. Determine the height of the next shelf, snap on supports, then add and secure shelf. Repeat for remaining shelves. (See Figure 6) Figure 6 1-800-295-5510 uline.com PAGE 2 OF 6 0423 IH-5466...
- Página 3 3. Utilice un martillo, mazo de caucho o golpee contra el piso hasta que el autonivelador se deslice dentro del poste. 4. Repita los pasos 2 y 3 para los otros postes. RUEDAS (ULINE MODELO# H-1205WH SE VENDE POR SEPARADO) 1. Asegúrese de que el poste esté posicionado como se muestra. Diagrama 2 (Vea Diagrama 2) 2.
- Página 4 Diagrama 5 3. Determine la altura de la siguiente repisa, ajuste los soportes al poste y luego agregue y asegure la repisa. Repita para las repisas restantes. (Vea Diagrama 6) Diagrama 6 800-295-5510 uline.mx PAGE 4 OF 6 0423 IH-5466...
- Página 5 à l'intérieur. 4. Répétez les étapes 2 et 3 pour tous les autres montants. ROULETTES (Nº DE MODÈLE ULINE H-1205WH, VENDU SÉPARÉMENT) 1. Assurez-vous que le montant est placé comme illustré. (Voir Figure 2) Figure 2 2.
- Página 6 (Voir Figure 5) Figure 5 3. Déterminez la hauteur de la tablette suivante, enclenchez les supports, puis ajoutez et fixez la tablette. Répétez l'étape 4 pour ajouter les tablettes restantes. (Voir Figure 6) Figure 6 1-800-295-5510 uline.ca PAGE 6 OF 6 0423 IH-5466...