Publicidad
Idiomas disponibles
Idiomas disponibles
4. Snap the waist buckle and adjust its length so that the
EN
backpack is securely supported by your hips
(Fig. L & M).
NOTICE:
The backpack shouldn't sit too high on your
back; it should be positioned closer to your hips than to
your shoulders.
5. Readjust the shoulder straps for security and comfort.
Makes sure that the backpack sits securely on your
back, with the weight supported by the waist strap,
and without excess movement when you move (Fig. N).
6. Insert any extra length of belt around the waist into the
elastic on both sides (Fig. O).
7. To detach the tool from your back, just press the waist
and chest buckles to release them and lower the tool
(Fig. P).
To Adjust The Control Handle
1. Loosen the wing nut to adjust the handle forward or
backward as needed (Fig. Q & R) and then tighten the
wing nut to secure the position of the handle.
2. You may also rotate the handle as needed for comfort
(Fig. S).
3. To enlarge the area you are cleaning, move the tube to
the left or the right (Fig. T).
TO START/STOP THE BLOWER (FIG. U)
Air-Speed Trigger Only
◾
Depress the air-speed trigger to turn on the blower.
◾
The air speed of the blower is controlled with the
variable speed trigger. More pressure on the trigger
results in higher blowing speeds; less pressure on
the trigger results in lower blowing speeds. Adjust the
speed to suit the task at hand.
◾
Release the air-speed trigger to turn off the blower.
Speed/Lock-On Dial Only
The blower can be turned on and locked at any speed
with the speed /lock-on dial.
◾
Turn the speed/lock-on dial clockwise to start the
blower. The air speed will increase as the dial is
rotated clockwise.
◾
To decrease the air speed, turn the speed/lock-on dial
counterclockwise.
◾
Keep turning the speed/lock-on dial counterclockwise
to the off position to stop the blower.
12
56 VOLT LITHIUM-ION CORDLESS BACKPACK BLOWER — LB6000E
Notice: If the speed/lock-on dial is not turned back to the
off position before turning the blower on, the blower will
not start through the speed/lock-on dial when a charged
battery is installed. This is a protection feature to help
prevent accidental startup. Depress the air-speed trigger
can deactivate the protection.
Press the boost button while working to temporarily
increase the air speed to the maximum level. The blower
will resume the previous speed when the boost button is
released.
Fig. U parts description see below:
U-1
Speed/lock-on Dial U-3
U-2
Boost Button
Tips For Using The Blower
◾
To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the
center of a pile.
◾
To reduce sound levels, limit the number of pieces of
equipment used at any one time.
◾
Use rakes and brooms to loosen debris before blowing.
In dusty conditions, slightly dampen surfaces if water
is available.
◾
Watch out for children, pets, open windows, or freshly
washed cars, and blow debris safely away.
◾
After using blowers or other equipment, clean up!
Dispose of debris properly.
◾
It is not recommended to use the blower at a high
speed for a long time, as large vibration and noise may
be harmful to your health.
MAINTENANCE
WARNING:
When servicing, use only identical
replacement parts. Use of any other parts may create a
hazard or cause product damage. To ensure safety and
reliability, all repairs should be performed by a qualified
service technician.
WARNING:
To avoid serious personal injury, always
remove the battery pack from the product when cleaning
or performing any maintenance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
Air-speed Trigger
Publicidad
