POLTI Forzaspira C 115 Manual De Instrucciones página 20

hose and the floor brush to the telescopic tube.
The length of the telescopic tube can be adju-
sted. Press the button to extend it or shorten
it at will (4).
5.3 Move the selector located on the brush,
pressing it with a foot, to the no-bristles posi-
tion (5).
5.4 Press the (6) switch. The appliance will
start to operate.
You can adjust the suction power with the
cursor(6).
5.5 To end suction, press the
again.
6. CLEANING UPHOLSTERY
(mattresses, sofas, car interiors, etc.)
6.1 Make sure that chapter 1 has been completed.
6.2 Connect the suction nozzle to the flexible
hose and pass over the surfaces.
Use the 2in1 lance for thorough vacuum clea-
ning of hard-to-reach spots such as skirting-
boards and folds in sofas, armchairs, uphol-
stered furniture and car upholstery. The
bristles of the 2in1 lance can be used by tur-
ning them 90 ° (7).
6.3 Press the (6) switch. The appliance will
start to operate.
You can adjust the suction power with the
cursor(6).
6.4 To end suction, press the
again.
With the manual cursor on the handle of the
flexible hose, it is possible to intervene
promptly in case of accidental suction (i.e.
curtains), reducing the suction power (8).
7. EMPTYING AND CLEANING THE
DUST CONTAINER
7.1 Switch off the appliance using the
switch. Disconnect the power supply cable
from the mains.
7.2 Unhook the dust container from the va-
cuum cleaner by opening the cover and pres-
sing the dust container release button (9).
7.3 Remove the dust container lifting it by the
handle.
7.4 Press the button located on the container
in order to open the container and remove the
dirt collected (10).
ATTENTION: since by operating the button
the lower base of the reservoir opens, it is
recommended that this operation be done
over a waste bin.
7.5 Remove the handle by turning it anti-
clockwise compared to the container, aligning
the two reference arrows (11).
7.6 Remove the container filter and pull out the
filter unit and remove any remaining dirt.
7.7 Replace the filter unit in the container,
making sure that the two arrows are aligned
(12).
(6) switch
7.8 Replace the air filter.
7.9 Reassemble the handle on the container
turning it clockwise, making sure to align the
two arrows (11).
7.10 Reposition the dust container on the ap-
pliance by repeating the steps described pre-
viously in the opposite order (13).
We recommend to clean the container after
each use.
WARNING: Do not use the appliance without
the dust container complete with filter.
WARNING: Never exceed the "MAX" level
shown on the dust container, otherwise the
filters will clog reducing the suction power of
the appliance.
8. GENERAL MAINTENANCE
(6) switch
Ensure that the appliance is switched off and
disconnected from the mains.
To clean the outside of the appliance, only use
a damp cloth and tap water.
Do not use detergents of any type.
8.1 CLEANING THE DUST CONTAINER
- Pull out the dirt container and remove the
container filter and the filter unit, as described
in the chapter 4.
(6)
- Rinse all the components under running wa-
ter and let them dry.
- Replace everything repeating the steps de-
scribed previously in the reverse order.
ATTENTION: Check all components of the du-
st collector are dry, before put them in order.
We recommend to clean the container after
each use.
8.2 REMOVING AND CLEANING THE HEPA
FILTER
- Turn the grill anti-clockwise (14) and remove
| 20 |