HK Audio LUCAS NANO 305 FX Manual página 11

4.4 Stereo System
With standard speaker stands and the POLE MOUNT ADAPTER
(see the picture below)
Setup
L R
Balance
L R
Use L/R Speaker Outs
Insert the POLE MOUNT ADAPTERs onto the 35 mm-diameter speaker
stands and use the Easy-Click connector to attach each satellite to a POLE
MOUNT ADAPTER. Be advised that the POLE MOUNT ADAPTER does not
route the signal to the satellite; you will have to use two speaker cables to
connect the subwoofer's Speaker Outs to the two satellites. Be sure to set
the Setup selector to 'Stereo Satellite and the Balance knob to the center or
12 o'clock position.
• Required accessories: 2x POLE MOUNT ADAPTERs
4.5 Stereo System
With an S-CONNECT POLE LN in combination with standard
microphone stands with a 3/8" thread or standard speaker tripods
and the POLE MOUNT ADAPTER
Setup
(L) R
Balance
L R
Use Speaker Out R
Screw the signal-carrying S-CONNECT POLE LN into the M33 mount on top
of the subwoofer. Lock one satellite in place with the S-CONNECT POLE
LN's Easy-Click mechanism. This satellite renders the left channel of the
stereo image. Attach the POLE MOUNT ADAPTER to the (35 mm diameter)
speaker pole. Connect the other satellite to the POLE MOUNT ADAPTER
via Easy-Click. Be advised that the POLE MOUNT ADAPTER does route the
signal in this setup. You have to plug one end of a speaker cable into the
subwoofer's Speaker Out R port and the other into the satellite's Speaker In
Pole Mount Adapter
Use with all
35 mm pole mounts
Two speaker
cables needed
4.4 Stereo System
with two POLE MOUNT ADAPTERs
and standard pole mounts
port to connect the two. Be sure to set the Setup switch to Stereo Satellite
mode and the Balance knob to the center or 12 o'clock position.
This setup option works with any standard microphone stand with a 3/8"
thread, in which case you won't need the POLE MOUNT ADAPTER.
• Required accessories: 1x S-CONNECT POLE LN, 1x POLE MOUNT
ADAPTER
4.6 Twin Stereo System
With 2 S-CONNECT POLE LNs + 1 LUCAS NANO LINK CABLE
(see the picture below)
Setup
Balance
L R
For usage without S-CONNECT POLE LN, use the Speaker Out L on both systems
It takes two LUCAS NANOs to set up a twin stereo system. First set up
each as a mono system as described in section 3.2, and then link the two
to create a twin stereo system using the two subwoofers' Link In/Out jacks
●
( 19 ). You will need the LUCAS NANO LINK CABLE or a shielded stereo cord
equipped with 1/4" (6.3 mm) jack plugs to do this.
Heads up: One system's Balance knob has to be turned to the left and
other's to the right.
Pairing up two systems to confi gure a twin stereo system gives you twice
the number of channels. The Master knob on each LUCAS NANO controls
the overall volume of that unit's master mix; that is, the channels that have
been blended to a composite signal. Be sure to set the Setup switches on
both systems to 'Satellite Array' .
• Required accessories: 2x S-CONNECT POLE LN / 1x LUCAS NANO LINK
CABLE
Pole Mount
Adapter
4.5 Stereo System
with one S-CONNECT POLE LN
+ one POLE MOUNT ADAPTER
LUCAS NANO 305 FX 1.1
Setup
Link In/Out
L R
Balance
Use
Stereo
Cable! L
4.6 Twin Stereo System
with two S-CONNECT POLE LN
+ one NANO LINK CABLE
R
Link In/Out
Stereo cable
11