Descargar Imprimir esta página

Husqvarna 960430242 Manual Del Operario página 18

Publicidad

Idiomas disponibles

Idiomas disponibles

V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
ad just able. Re place belts if they begin to slip from wear.
TRANSAXLE MAINTENANCE
The transmission fan and cooling fi ns should be kept clean
to ensure proper cooling.
Do not attempt to clean fan or transmission while engine
is running or while the transmission is hot. To prevent pos-
si ble damage to seals, do not use high pressure water or
steam to clean transmission.
Inspect cooling fan to be sure fan blades are intact and
clean.
Inspect cooling fi ns for dirt, grass clippings and other
materials. To prevent damage to seals, do not use com-
pressed air or high pressure sprayer to clean cool ing fi ns.
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and fl uid main te-
nance is not required for the life of the transaxle. Should
the transaxle ever leak or require servicing, contact your
near est au tho rized ser vice center/department.
ENGINE
LUBRICATION
Only use high quality detergent oil rated with API service
classifi cation SJ-SN. Select the oil's SAE viscosity grade
according to your expected operating temperature.
SAE VISCOSITY GRADES
5W-30
-20
0
30
F
C
-30
-20
-10
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
Change the oil after every 50 hours of operation or at least
once a year if the tractor is not used for 50 hours in one year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation.
TO CHANGE ENGINE OIL (See Fig. 19 - 21)
Determine temperature range expected before oil change.
All oil must meet API service classifi cation SJ-SN.
Ensure tractor is on level surface.
Oil will drain more freely when warm.
Catch oil in a suitable container.
LOWER DASH COVER REMOVAL
Raise hood.
Remove fastener from lower dash cover.
MAINTENANCE
10W30
32
40
60
80
0
10
20
30
Fig. 19
CAUTION: Remove lower dash cover carefully to ensure
cover tabs are not broken.
Slide lower dash cover up to release cover tabs from
tapered slots in lower dash and remove.
LOWER DASH COVER
Remove oil fi ll cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
Install the drain tube onto the valve.
Open drain valve by using a 10mm wrench turning
counterclockwise.
TO OPEN
After oil has drained completely, close the drain valve
turning clockwise. Use the 10mm wrench to apply a small
amount of torque to keep it closed. Do not over tighten.
100
Remove the drain tube and store in a safe place.
40
Refi ll engine with oil through oil fi ll dipstick tube. Pour
slowly. Do not overfi ll. For approximate capacity see
"PRODUCT SPECIFICATIONS" section of this man u al.
Use gauge on oil fi ll cap/dipstick for checking level.
Insert dipstick into the tube and rest the oil fi ll cap on
the tube. Do not thread the cap onto the tube when
taking reading. Keep oil at "FULL" line on dipstick.
Tighten cap onto the tube securely when fi nished.
ENGINE OIL FILTER
Replace the engine oil fi lter every season or every other
oil change if the tractor is used more than 100 hours in
one year.
NOTE: If needed, remove lower dash covers using steps
from "Lower dash cover removal" section of this manual.
18
FASTENER
TABS
Fig. 20
OIL DRAIN VALVE
TO CLOSE
Fig. 21
SLOTS
DRAIN
TUBE

Publicidad

loading

Este manual también es adecuado para:

Ts 348xd960430289960430319960430320