Bosch GSR Professional 36 V-LI Manual Original página 21

OBJ_BUCH-487-001.book Page 21 Thursday, August 23, 2007 9:18 AM
Noise/Vibration Information
Measured values determined according to
EN 60745.
GSR 36 V-LI:
Typically the A-weighted sound pressure level of
the product is less than 70 dB(A). The noise lev-
el when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Drilling into metal: Vibration emission value
2
a < 2.5 m/s , Uncertainty K =1.5 m/s
h
Screwdriving: Vibration emission value
2
a < 2.5 m/s , Uncertainty K =1.5 m/s
h
GSB 36 V-LI:
Typically the A-weighted noise levels of the
product are: Sound pressure level 86 dB(A);
Sound power level 97 dB(A). Uncertainty
K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Drilling into metal: Vibration emission value
2
a =3.0 m/s , Uncertainty K =1.5 m/s
h
Impact drilling into concrete: Vibration emission
2
value a = 11.5 m/s , Uncertainty K =1.5 m/s
h
Screwdriving: Vibration emission value
2
a < 2.5 m/s , Uncertainty K =1.5 m/s
h
GSR 36 V-LI/GSB 36 V-LI:
The vibration emission level given in this infor-
mation sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another.
It may be used for a preliminary assessment of
exposure.
The declared vibration emission level repre-
sents the main applications of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may signifi-
cantly increase the exposure level over the total
working period.
Bosch Power Tools
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that
2
,
the product described under "Technical Data" is
in conformity with the following standards or
2
.
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 98/37/EC (until Dec. 28, 2009),
2006/42/EC (from Dec. 29, 2009 on).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
2
,
2
,
2
.
16.07.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
Battery Charging
Use only the battery chargers listed on the
accessories page. Only these battery charg-
ers are matched to the lithium ion battery of
your power tool.
Note: The battery is supplied partially charged.
To ensure full capacity of the battery, complete-
ly charge the battery in the battery charger be-
fore using your power tool for the first time.
English | 21
Dr. Eckerhard Strötgen
Head of Product
Certification
1 609 929 M41 | (23.8.07)