Cooper Lighting Solutions HALO ESF2ARGBWFB-WiZ Instrucciones página 3

Problem
Unable to find luminaire on
the network.
Unable to operate
luminaire with the
connected light switch.
Luminaire not responding
to WiZ APP control.
Luminaire not connecting
to the WiZ APP .
Fixture not turning ON
after power outage.
Wiz App related question and information, please visit: https://faq.wizconnected.com/hc/en/3-wiz/
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
•
(1) This device may not cause harmful interference.
•
(2) This device must accept any interference received, including interference that may cause undesired operation.
•
N ote: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could
void the user's authority to operate the equipment.
N ote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
•
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help
•
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
•
minimum distance of 20 cm between the radiator and your body.
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt
•
RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
This device complies with ISED ICES Standard Canada ICES-005(B) / NMB-005 (B)
•
Smart Wi-Fi Security Floodlight WiZ instructions
TROUBLESHOOTING
Possible Cause
Luminaire may not be in Connectivity Mode.
Wiring issue.
No electricity.
Network is not connected.
Luminaire may not be paired correctly.
Permissions are not granted on mobile
device.
Wi-Fi password is incorrect.
Weak/low Wi-Fi signal.
Wi-Fi not connected.
"Power outage Recovery" setting from WiZ
app is ON.
www.cooperlighting.com
Solution
Cycle the light switch connected to luminaire ON/OFF 3 times to
•
enter Pairing Mode.
Refer back to WiZ App Help center for FAQ's.
•
Review and confirm the INSTALLATION instructions.
Check that the power is ON at the connected light switch and
circuit breaker.
Check the wireless network connectivity.
•
Refer back to WiZ App Help center for FAQ's.
•
Cycle the light switch connected to luminaire ON/OFF 3/5
•
times until light start to pulse in blue (color light) or cool white
(tunable white light) to enter Pairing Mode.
Refer back to WiZ App Help center for FAQ's.
•
Check to see that permissions are granted for the WiZ APP .
•
Refer back to WiZ App Help center for FAQ's.
•
Re-enter Wi-Fi password.
•
Refer back to WiZ App Help center for FAQ's.
•
Check Wi-Fi signal to ensure within range of router.
•
Refer back to WiZ App Help center for FAQ's.
•
Confirm Wi-Fi router is broadcasting a 2.4 GHz signal.
•
Re-connect.
Refer back to WiZ App Help center for FAQ's.
•
Change the "Power outage recovery" setting to OFF .
Go to Settings> Others> Power Outage Recovery.
FCC STATEMENT
3