Lorelli LYNX Instrucciones De Uso página 13

INSTALLATION OF SEAT "Group 0+" / newborn and weighing up to 13 kg. /
Attaching of the car seat with ISOFIX and Top tether.
IMPORTANT: First please check if there are 2 ISOFIX anchorings in the perpendicular intersection of the
vehicle seat back and seat cushion, and the user-ready top tether anchoring behind the vehicle seat.
Tips: The user-ready tether anchorage usually permanently installed on the inner rear luggage shelf or on the
vehicle floor. For details you could read your vehicle guidelines or contact the vehicle manufacturer.
NOTE: When using the ISOFIX system, the ISOFIX guide sleeves can be inserted into the ISOFIX
anchorages on the vehicle. ( Picture 13;17-1) The ISOFIX anchorages on both ends are pushed inward along
the guide sleeves.
Step 1. Group 0+: The child seat can be used only in the most backward inclined position. (Picture 2 , Pos.4)
Pull the positioning handle and place the child seat in the most backward inclined position (Picture 1;2 )
Step 2. Press the Release button to release the ISOFIX connectors. Than you can hear an audible sound
"click" Picture 14 Slide the rails till the longest position .
Step 3 . Pull and hold the release handle for rotation of the child seat "5 " and rotate the seat at 180 º
so that the marking of the seat to match with position the blue position on the base. Picture 15
Release the handle and ensure that the child seat is fixed.
WARNING ! DO NOT USE THE CHILD SAFETY SEAT ADJUSTED AT 90º OF THE SIDE OF MOVEMENT
OF THE CAR !!! THIS CHILD SEAT SHOULD BE USED ONLY AT FOREWARD OR REARWARD SIDE OF
THE MOVEMENT OF THE CAR !!!
Step 4 . Place the child seat on the seat of the car, it must be oriented in the direction opposite to the
movement! Picture 16 This is the safest position for your child so it is advisable to use it as long as
possible! If your car has an air bag on the passenger seat, the child seat should be used only in the rear of
the car!
Step 5. Push the ISOFIX connectors directly into the anchorages until you hear an audible sound "click".
Picture 16 Make sure that you have heared a "click " and the ISOFIX latching indication shows GREEN
Picture 17.03
Step 6. Push firmly the child seat towards the car seat backrest. Picture 17 During this moving the ISOFIX
system will tighten the child seat to the car seat backrest and you will hear a "Click"sound . Ensure that the
child seat is firmly pressed to the car seat backrest. Check the ISOFIX release button again and ensure the
latching indication shows GREEN. Picture 17
Step 7. Grasp the seat body to check the seat if it is fastened tightly or shakes. If the seat shakes and the
ISOFIX connectors are pulled out, please repeat the above steps and install it again. Picture 18
Step 8. Pull out the Top tether and press the Tether strap release button to extend the strap until it is long
enough to hook the User-ready tether anchorage behind. Picture 19 Guide the top tether around the both
sides of the backrest of child seat and around the headrest of the car. Picture 20
Step 9. Hook the Tether strap hook onto the User-ready anchorages. Check there maybe are 3 anchorages
for the hook, please find one in your favor. Picture 21
Step 10. Pull the Tether strap on another end back to tighten the Top tether.
CAUTION: If the Top tether is tightened favorably and correctly, a green mark will turn up on the other end of
the Strap release button, please do check it. Picture 22
Step 11. Place the child in the seat. Check the height of the shoulder belts. Make sure the straps are not
twisted or hanging somewhere. Fasten the seat belts on the child, making sure that they are well placed and
pull the strap in the centre of the seat to tighten. Ensure five points buckle is locked ( Picture 4;5;6;7;8;9)
INSTALLATION OF SEAT "Group 0+" / newborn and weighing up to 13 kg. /
Please use 3-point safety belts of the car to secure the child seat!
Step 1. Group 0 + The child seat can be used only in the most backward inclined position. (Picture 24) Pull
the positioning handle and place the child seat in the most backward inclined position (Picture 1;2;23;24 )
This is the safest position for your child so it is advisable to use it as long as possible.
Step 2. Pull and hold the release handle for rotation of the child seat "5 " and rotate the seat at 180 º
so that the marking of the seat to match with the blue position on the base. Picture 18;26
Step 3 . Place the child seat on the seat of the car, it must be oriented in the direction opposite to the
movement. ( Picture 25) If your car has an air bag on the passenger seat, the child seat should be used
only in the rear of the car!
Step 4. Unlock the harness and lift up the inner cushion. Picture 26 Pull out the entire car seat belt. Pass the
lap part of the seat belt thought the guide holes at the both sides of the safety seat (Picture A position 24) and
fasten the clip to the corresponding buckle till click is heard. Check that the belt buckle is locked by pulling
the belt. ( Picture 28)
With 3-point seat belt
13