Step 5. Pass the upper diagonal part of the belt in the belt guide behind the seat back, and pull to fasten the
belt. Picture 29;30 Put the inner cushion back. (Picture 31)
Step 6. Make sure that the belt is not twisted and strongly tightened. Make sure the seat is fixed firmly on the
car seat. ( Picture 32)
Step 7. Place the child in the seat. Check the height of the shoulder belts. Make sure the straps are not
twisted or hanging somewhere. Fasten the seat belts on the child, making sure that they are well placed and
pull the strap in the centre of the seat to tighten. ( Picture 4;5;6;7;8;9)
Please use 3-point safety belts of the car to ensure the safety of the child and to secure the child seat!
Step 1. Place the child seat on the car seat forward-facing and make sure that the back of the child seat is
firmly pressed against the car seat backrest. Picture 36 WARNING ! Make sure that the child seat is
correctly adjusted for installation at forward position . If it's needed pull the adjusting handle "5 "
( Picture A) and rotate the seat in forward position.
Step 2. Pull out the entire car seat belt. Picture 36 Pass the diagonal belt between the backrest and headrest
through the belt guide and lap belt through the belt guides at the bottom of child's seat as shown at Picture 37
Make sure that the both parts of the car belt are under the harness of the child seat !
Step 3. Clip the lap belt and diagonal belt into the car buckle until hear a "Click" and then pull them to tighten
the child seat. ( Picture 38;39)
Step 4. Place the child in the seat. Check the height of the shoulder belts. Make sure the straps are not
twisted or hanging somewhere. Fasten the seat belts on the child, making sure that they are well placed and
pull the strap in the centre of the seat to tighten. ( Picture 4;5;6;7;8;9)
INSTALLATION OF SEAT "Group I" / 9 to 18 kg./
With 3-point seat belt + additional attachment (FIT).
Step 1. IMPORTANT: First please check if there are 2 ISOFIX anchorings in the perpendicular intersection of
the vehicle seat back and seat cushion, and the user-ready top tether anchoring behind the vehicle seat.
NOTE: When using the ISOFIT system, the ISOFIX guide sleeves can be inserted into the ISOFIX
anchorages on the vehicle. (Picture 13; 35.1) The ISOFIX anchorages on both ends are pushed inward along
the guide sleeves
Step 2. Press the Release button to release the ISOFIX connectors. (Picture 14) Than you can hear an
audible sound "click" Slide the rails till the longest position. WARNING ! Make sure that the child seat is
correctly adjusted for installation at forward position . If it's needed pull the adjusting handle "5 "
( Picture A) and rotate the seat in forward position.
WARNING ! DO NOT USE THE CHILD SAFETY SEAT ADJUSTED AT 90º OF THE SIDE OF MOVEMENT
OF THE CAR !!! THIS CHILD SEAT SHOULD BE USED ONLY AT FOREWARD OR REARWARD SIDE OF
THE MOVEMENT OF THE CAR !!!
Step 3. Place the child seat on the seat of the car, it must be oriented in the direction of movement.
Picture 34;35 If your car has an air bag on the passenger seat, the child seat should be used only in the
rear of the car!
Step 4. Push the ISOFIX connectors directly into the anchorages until you hear an audible sound "click".
Make sure that you have heard a "click " and the ISOFIX latching indication shows GREEN Picture 35
Step 5. Push firmly the child seat towards the car seat backrest. During this moving the ISOFIT system will
tighten the child seat to the car seat backrest and you will hear a "Click" sound . Ensure that the child seat is
firmly pressed to the car seat backrest. Check the ISOFIX release button again and ensure the latching
indication shows GREEN.
Step 6. Grasp the seat body to check the seat if it is fastened tightly or shakes. If the seat shakes and the
ISOFIT connectors are pulled out, please repeat the above steps and install it again.
Step 7. Please repeat the steps from 2 to 4 for installation on the car seat described in Group I /9 to 18 kg. /
with 3 - Point Belt
INSTALLATION OF SEAT
"Group I" / 9 to 18 kg. / With 3 - Point Belt
14