ETI Solid State Lighting SWPK-1-LB3-CP3-MV-LVDSWPK-1-LB4-CP3-MV-LVD Guía De Uso Y Cuidado

Order # 61506101
Use and Care GUide
Led seCUrity WaLL PaCk
120-277V 50/60Hz 15W/20W/30W
Package contents
Description Quantity
Fixture 1
EVA Foam 1
Terminal 3
nOte: Keep your receipt and these instructions for proof of purchase. To avoid possibility of electrical shock or fire, the installation personnel must have professional electric
knowledge. Please wear gloves to avoid injury before installation. If any smoke or spark of the wire happened, please turn off the power immediately and notify relevant personnel.
WarninG: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes. Do not use the electric generator to test the LED lamp.
Please abide by related country, regional and local law and regulations when install this fixture. Please don't install the fixture when raining to lower the risk of electric shock and
avoid the failure.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
aPPLiCatiOn: Industrial lighting, landscape lighting, courtyard, building, hotel, building exterior, etc.
InstallatIon
Turn off the power. Remove the rubber plugs and loosen 4 screws.
1 2
ON
OFF
Peel off the yellow sticker and paste it on the Fix the bottom plate on the round plate.
4 5
round area of the bottom plate.
Replace the cover by the 4 screws, fill the Check that the wiring and screws are tightened
7 8
holes with rubber plugs. and secured, then turn on the power.
Part # sWPk-1-LB3-CP3-MV-LVd Certification # sWPk-1-LB3-CP3-MV-LVd
Fixture EVA Foam
Remove the 1/2 end cap.
3
Connect the wiring and make sure to secure the
6
ends with wire caps.
ON
OFF
cct & Wattage aDjustment
1 Color Temperature Adjustable
Adjust the CCT via switch (selectable 3000K = 3K/ 4000K = 4K/ 5000K = 5K), as shown below.
Wattage Adjustable
2
Adjust the wattage via switch, with three optional settings (low/medium/high), as shown below.
Terminal
Warning/avertissement:
MIN 90°C SUPPLY CONDUCTORS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED
LES FILS D'ALIMENTATION 90 °C MIN
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENTAINSI QUE LES RISQUES
INHÉRENTS.
WarninG: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
nOtiCe: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
or
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-etI-sslI (1-855-384-7754) www.etissl.com