Descargar Imprimir esta página

Ingersoll Rand R140-KL1 Manual Del Usuario página 29

Publicidad

Idiomas disponibles

Idiomas disponibles

Product Information: Cordless Ratchet - R140, R145, R380, and R385
Product Safety Information
Intended Use:
These Cordless Ratchet Wrenches are designed to remove and install threaded fasteners.
Responsibly recycle or dispose of Batteries. Do not puncture or burn Batteries. Improper disposal may endanger the environment or
cause personal injury.
Only use Tools with appropriate voltage Ingersoll Rand Batteries and Charger. Use of any other batteries may create a risk of fire,
personal injury or property damage.
This is a class A product. In a residential, commercial or light industrial environment it may cause radio interference. This product is
not intended to be installed in a residential environment; in a commercial and light industrial environment with connection to the public
mains supply, the user may be required to take measures to reduce interference.
For additional information, refer to Cordless Ratchet Wrench Safety Information Manual Form 80232929, Battery Charger Safety
Information Manual Form 10567832 and Battery Safety Information Manual Form 10567840.
Manuals can be downloaded from www.ingersollrandproducts.com
Product Specifications
Voltage
Drive
Model
V, DC
inch
R140
7.2
R145
7.2
R380
14.4
R385
14.4
† K
= 3dB measurement uncertainty
pA
‡ K
= 3dB measurement uncertainty
wA
*K = Vibration measurement uncertanity
When using this product as a manually-operated ratchet wrench, do not exceed the maximum torque listed in the table. Exceeding this
torque may cause damage to the product and will void the warranty.
Product Operation
These models feature a variable trigger and an automatic shut-off.
The variable trigger feature allows an operator to regulate the power output of the tool through manipulation of the trigger lever. Power output
will increase as the trigger lever is pressed in, with maximum power output occurring when the trigger lever is fully depressed. Power output
will decrease as the trigger lever is released.
The automatic shut-off feature shuts off power to the motor when the motor is stalled. When tightening a fastener, the motor will stall when the
tool is unable to tighten the fastener any further, so automatic shut-off will occur at this condition. When attempting to loosen a fastener, the
motor will stall if the tool is unable to move the fastener, so automatic shut-off will occur at this condition also. When automatic shut-off occurs,
the trigger lever must be fully released and then pressed again to restart the tool. After automatic shut-off occurs, the tool can continue to be
used as a manually-operated ratchet, provided that the maximum torque limit specified for that particular model is not exceeded.
Parts and Maintenance
For routine maintenance:
of Ingersoll Rand #70 grease between the ratchet housing and the yoke to lubricate the drive bushing.
Monthly, inject 1 cm
3
After every 3 months of use, disassemble the ratchet head and lubricate the components with 2 cm
After every 6 months of use, disassemble the gearing and lubricate the components with 1 cm
All other maintenance and tool repair should only be carried out by an authorized Service Center. For the nearest location, visit
www.ingersollrandproducts.com
Refer all communications to the nearest Ingersoll Rand Office or Distributor.
45619400_ed2
No Load
Recommended
Speed
Torque Range
rpm
ft-lbs (N-m)
1/4
0-225
5-25 (7-34)
3/8
0-225
5-25 (7-34)
3/8
0-225
10-60 (14-81)
1/2
0-225
10-60 (14-81)
WARNING
Max. Torque
ft-lbs (N-m)
† Pressure (L
25 (34)
25 (34)
70 (95)
70 (95)
NOTICE
Sound Level dB (A)
(ISO 15744)
)
‡ Power (L
)
p
w
74.9
85.9
74.9
85.9
80.8
91.8
80.8
91.8
of Ingersoll Rand #70 grease.
3
of Ingersoll Rand #67 grease.
3
EN
Vibration m/s
2
(ISO 28927)
Level
*K
<2.5
---
<2.5
---
4.9
0.9
4.9
0.9
EN-1

Publicidad

loading