Publicidad
5) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
ADDITIONAL SAFETY WARNINGS
1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. To prevent accidents, the plug is disconnected from
the receptacle before any adjustments, conversions or
servicing are performed.
4. The work place must be well ventilated.
5. Follow national requirements for the materials you want
to work with.
6. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
7. Attaching and removing the dust bag
Prior to the sanding operation, make sure the material of
surface you are going to sand.
If the surface under sanding operation is expected to
generate harmful / toxic dusts such as lead painted
surface, make sure the dust bag or appropriate dust
extraction system is connected with dust outlet tightly.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts generated
in sanding operation, the dust can endanger the health
of yourself and bystanders.
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful.
Certain kinds of dust are classifi ed as carcinogenic
such as oak and beech dust especially in conjunction
with additives for wood conditioning (chromate, wood
preservative).
Material containing asbestos must only be treated by
specialists.
8. Practical operating procedures
○ Never apply water or grinding fl uid when sanding. This
could result in electrical shock.
○ Never turn the power switch ON when the sander is
contacting the surface to be sanded. This is necessary
to preclude damage to the material. The same applies
when switching the power OFF.
○ DO NOT apply excessive pressure to the sander while
sanding. Excessive-pressure may cause overload of the
motor, reduced service life of the sanding paper, and
lowered sanding or polishing effi ciency.
9. Wear ear protectors when working for long periods of
time.
High noise levels over a prolonged period of time may
aff ect your hearing.
10. Materials that generate dusts or vapours that may be
harmful to health (e.g. asbestos) must not be processed.
11. Secure the workpiece against slipping, e.g. with the help
of clamping devices.
12. RCD
The use of a residual current device with a rated residual
current of 30mA or less at all times is recommended.
13. In the following cases, clean the dust bag and fully
remove any dust.
Dust remaining in the dust bag may cause ignition.
• Sanding steel sheets after sanding materials such as
wood
• After completing polishing work
14. When using the front handle, make sure to use it with the
knurled screw fully tightened.
15. When commencing work, make sure that the enclosure
is not cracked.
16. Do not throw sanding dust on an open fi re because
materials in fi ne particle form may be explosive.
17. Do not use for any application other than its intended use.
18. Never switch on the tool when it is in contact with the
workpiece, it may cause an injury to operator.
SYMBOLS
WARNING
The following show symbols used for the machine. Be
sure that you understand their meaning before use.
SV15YC: Random Orbit Sander
To reduce the risk of injury, user must read
instruction manual
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Rated voltage
Ensure that the power source to be utilized
V
conforms to the power requirements specifi ed
on the product nameplate.
D
Diameter of Sanding paper
P
Power input
No-load speed
n
0
(TurboBoost switch OFF)
No-load speed
n
0, TB
(TurboBoost switch ON)
S
Orbit diameter
Weight (Without cord)
kg
Switching ON
Switching OFF
TurboBoost switch
Disconnect mains plug from electrical outlet
Warning
Class II tool
7
English
Publicidad
