Elframo D36 Serie Manual Del Usuario página 24

glasses and causes an excessive foam formation in the tank. Whereas dishes covered by water drops or a long
drying period indicate that there is not enough rinse-aid or that there is a light layer of amid which can be removed
by putting the dishes into a basin with water and enough detergent (1:10) for some minutes.
8. Electric detergent dispenser (optional)
During rinsing the peristaltic dispenser is activated to inject the detergent into the tank. Before using the machine,
the dispenser and the feeding tube have to be filled up. Make sure that the detergent reserve bin is full.
To fill up the plastic tube of the detergent feeding: run the first water charging without the overflow pipe in its place
until the feeding tube is full. To calibrate the correct quantity contact a qualified technical assistance service.
9. Electric rinse-aid dispenser (optional)
During washing, the peristaltic dispenser is activated to inject the rinse-aid into the boiler. The rinse-aid dispenser
and its feed tube must be filled before using the machine. To do this, make sure that the rinse-aid reserve bin is
full. During the washing phase open and close the machine door briefly for a few times and alternate with at least
10 seconds pauses until the feeding tube is filled up. To calibrate the correct quantity contact a qualified technical
assistance service.
10. Levelling of the water
To fill up the tank or when the water level in the tank is too low, the solenoid valve and the electric rinsing pump (if
fitted) are activated. Once the water reaches the correct level, the levelling is stopped (the rinsing solenoid valve
goes off with a 15 seconds delay only after the first filling). During the entire filling phase the cycle start button A-2
is deactivated.
11. Washing cycle
The washing cycle includes 3 phases: WASHING, PAUSE, RINSING and is activated by pressing the A-2 button.
The lengths of the washing phase (short, normal and long cycle) can be selected by using the A-3 cycle selection
button. During the entire cycle lengths the cycle LED A-6 of the selected lengths is blinking (freq. 1 second).
The cycle is not started if:
•
the water level is not correct (or if the machine is filling up)
•
the door is opened
•
the machine is off or in regeneration mode
12. Selecting the cycle times
The short, normal and long washing cycle can be selected by pressing the A-3 button. Each time the A-3 button is
pressed the relating LEDs A-6 go on and off to indicate the selected cycle time. By pressing the A-2 button the
washing pump is activated; the cycle LED A-6 of the selected time blinks during the cycle operation (freq. 1
second). At the end of the washing phase the pause is activated for 5 seconds. The washing phase time can be
automatically extended due to following conditions:
Should the boiler heating element still be heating while the washing cycle is started, the cycle runs normally but the
count-down of the cycle is interrupted 10 seconds before its normal end and will only be restarted when the heating
element is off. The cycle continuous normally with the next phase.
Note: If the boiler heating element does not switch off, the cycle continuous for max. 8 minutes, after which the
pause and the rinsing phases are activated; the A-5 LED blinks (freq. 0,3 seconds) and continues to blink also after
the cycle ends. To reset the LED it is necessary to switch the machine off and on again (A-1 button). Please
contact customer service to verify the problem.
13. Continuous cycle
To activate a continuous cycle it is necessary to press the A-3 button until all A-6 LEDs are on at the same time. At
this point it is possible to press the A-2 button to run the continuous cycle. For the continuous washing cycle the
limit is 8 minutes, after which pause and rinsing are activated. Only the continuous cycle may be manually
shortened by pressing the A-2 button to switch to the pause phase before the 8 minute washing phase is
completed.
14. Opening the door during the cycle
If the door is opened during the washing cycle, the cycle is interrupted and when the door is closed again the cycle
continuous from the previous point.
Note: If the softstart function is enabled the washing pump is always reactivated in this mode.
15. Regeneration cycle (if present)
The average frequence for this operation is about 40 baskets (referred to an initial hardness of 35 French grades).
This value may change according to water hardness; matt strains on the glasses indicate the necessity to proceed
with the regeneration. Make sure that there is enough kitchen salt in the plastic bin inside the tank (1kg is sufficient
for 5 regenerations). The regeneration cycle can only be activated when the machine is on and the front door is
closed. Now press the A-4 button for at least 3 seconds. The regeneration phase starts by switching on the relevant
Istruzioni originali Original instructions Instructions originales Originalanleitungen Instrucciones originales Rev. 3.00 del 14/02/2020 - pag. 24 di 72
EN