Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
To ensure safe operations and service of the instrument, follow these
instructions. Failure to observe these warnings can result in re,
electric shock, severe injury or death.
The Digital Probe-Pro is designed for use on extra-low voltage cabling
•
systems (less than 60V) for testing when NOT energized.
DO NOT use instrument if wet, as it could pose a shock hazard.
•
DO NOT use instrument if damaged in any way.
•
Turn off instrument before attempting to replace batteries.
•
The battery door must be in place and secure before you operate the
•
instrument.
DO NOT open the case, other than the battery compartment.
•
READ ALL INSTRUCTIONS BEFORE OPERATING AND RETAIN
INSTRUCTIONS FOR FUTURE REFERENCE
TURNING DIGITAL PROBE-PRO AND WORKLIGHT ON/OFF
1. Turn the probe on by pressing the Power On/Off Button
Turn the probe on by pressing the Power On/Off Button
2. When the probe is on, press the Power On/Off Button
3. To turn off the probe, press and hold the Power On/Off Button
than 2 seconds.
TRACING PAIRED WIRES (FIG. 1)
1. Connect tone generator (VDV500-163 Digital Toner-Pro recommended, sold
seperately) to the wires of the pair to be traced, per tone generator's instructions.
seperately) to the wires of the pair to be traced, per tone generator's instructions.
2. Turn the Digital Probe-Pro on by pressing the Power On/Off button
3. At the far end of the cable, spread the wires apart at least 2" (51 mm), if possible.
4. If performing analog toning, first ensure the Digital Toner-Pro is set to analog
toning mode (refer to VDV500-163 instruction manual.) Then ensure the
Digital Probe-Pro is set to analog mode by pressing the Analog Mode button
Digital Probe-Pro is set to analog mode by pressing the Analog Mode button
. The Analog Mode Button will illuminate green when in analog mode. If
P12 P12 P12
performing digital toning, first ensure the Digital Toner-Pro is set to digital
toning mode (refer to VDV500-163 instruction manual.) Then ensure the
Digital Probe-Pro is set to digital mode by pressing the Digital Mode Button
Digital Probe-Pro is set to digital mode by pressing the Digital Mode Button
. The Digital Mode Button will illuminate blue when in digital mode.
P11 P11
5. Use the Digital Probe-Pro to scan the cable's wire pairs. Move the Digital Probe-
Use the Digital Probe-Pro to scan the cable's wire pairs. Move the Digital Probe-
Pro's tip
slowly across the wires (FIG. 1). The Digital Probe-Pro's volume
slowly across the wires (FIG. 1). The Digital Probe-Pro's volume
slowly across the wires (FIG. 1). The Digital Probe-Pro's volume
slowly across the wires (FIG. 1). The Digital Probe-Pro's volume
P1
and Signal Strength Indicator bars
toned pair. When the Digital Probe-Pro's volume and Signal Strength Indicator
bars are high over the first wire, low in the middle (between) the two wires, and
high over the second wire, you have located the pair of wires you are tracing.
high over the second wire, you have located the pair of wires you are tracing.
high over the second wire, you have located the pair of wires you are tracing.
Use the Volume Increase
volume.
FIG. 1
2"
(51 mm)
4
WARNINGS
OPERATING INSTRUCTIONS
P4
and Volume Decrease
and
P6
to turn the worklight on/off.
to turn the worklight on/off.
to turn the worklight on/off.
P3
+ +
will increase as it approaches the
will increase as it approaches the
P5
P7
once.
once.
P3
for more
for more
P3
.
P3
buttons to adjust the
buttons to adjust the
VDV500-163
(sold seperately)
Publicidad
