Publicidad
GB
IMPORTANT SAFETY NOTES
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery,longhairorotherloose
objects away from opening!
Warning:
Moving parts can crush and cut!
CONTROLS:
1 = Mains plug (fig. 2)
When the machine is first plugged in it is not
on.
2 = Function buttons (fig. 1)
"Ready"/ "Off" / "Stop"
This button has three functions:
a) "Ready"
The machine changes to "Ready" if you
press this button briefly.
At the same time the integral LED display
comes on.
b) "Off"
The machine switches off if it is in the "Ready"
mode and the button is held down for about 3
seconds.
Note: The machine switches off automatically
if it is not used for about 5 minutes.
c) "Stop"
If you press this button briefly when the
cutters are running they switch off and stop.
6
7
8
2
fig. 1
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine
off with the mains switch, or unplug the
machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
Special materials
Symbol
Model
120SC2 - 3,8
120SC2 - 5,8
120CC3
120CC4
120CC5
X
120CC6
X
X = not applicable for shredding
Warning:
Electrical Hazard!
OPERATION
3 = Forwards button (fig. 1)
This button has two functions:
a) If this button is pressed briefly, the cutting
mechanism runs forwards for a few seconds,
e.g. to remove remaining material from the
cutting mechanism. At the same time the
integrated LED display
b) If this button is pressed and held for approx.
two secs., the cutting mechanism runs
forwards continually and materials to be
shredded can be fed into the machine. At
the same time the integrated LED display
lights up.
4 = Reverse button (fig. 1)
If you press this button the cutters run backwards
for a short time. At the same time the integral
LED display
comes on.
5 = Light barrier (Forward motion) (fig. 3)
The shredding procedure starts as soon as
material is fed into the feed slot. At the same
time the integral forward button LED display
comes on.
3
9
10
1
4
fig. 2
AREA OF APPLICATION:
The
data shredder is a machine used for shredding
general documents.
INSTALLATION:
- Unpack the machine and put it together.
- Attach the Power Cord to the Power Connection
X
X
X
X
X
X
X
X
X
6 = Control display (fig. 1)
lights up.
5
INITIATION
intimus
120SC2/CC3/CC4/CC5/CC6
Generally the machine may only be
used to shred paper (deviations see
table below "special materials")!
Shredding of other types of data carriers
may lead to injuries (for example due to
splintering of hard materials etc.) and
damage to the machine (for example
destruction of the cutter etc.).
on the machine and plug into an AC outlet (1)
(Fig. 2) (For information on the right fuse for
the plug see "TECHNICAL DATA").
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
Keep enough distance to the surroun-
dings when installing the machine.
"Material jam in machine"/ "Light barrier
covered when door opens or when machine
turned on"
For the procedures see the relevant description
under the "MALFUNCTION" section.
a) "Material jam in machine"
Comes on when too much material has been
fed into the cutters. The cutters jam, then
run in reverse for a short time and stop. The
motor switches off.
b) "Light barrier covered
when door open"
Comes on when there is still material in
the feed slot when the door is opened. The
cutters stop. The motor switches off.
c) "Light barrier covered
when machine turned on"
Comes on when there is still material in the
feed slot when the machine is switched on.
11
fig. 3
5
Publicidad
