EarthWise CVP41810BB Manual Del Propietário página 13

BEFORE USING: Fill oil well with new quality bar and chain oil.
Unused SAE30 weight motor oil may be substituted.
If you drop the product, carefully inspect it for damage. If the blade is
bent or cracked, handles broken or if you see any other condition that
may affect the product's operation, it must be repaired before putting
it back into use. Call our customer service help line at 1-800-313-
5111 for assistance.
CAUTION: Do not at any time let brake fluids, gasoline, petroleum
based products, penetrating oils, etc., come in contact with plastic
parts. They contain chemicals that can damage, weaken or destroy
plastic.
Make sure the unit is detached from the power supply, then use only
mild soap and a damp cloth to clean the tool. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment should be performed by a
qualified individual using identical replacement parts only.
Ensure that the plastic bar covers are in place when storing.
For smooth and fast cutting, chain needs to be maintained properly.
The chain requires sharpening when the wood chips are small and
powdery, the chain must be forced through the wood during cutting,
or the chain cuts to one side. Refer to instructions earlier in this
manual for instructions on properly sharpening the chain.
LUBRICATION SYSTEM FOR CHAIN SAW
The chain is automatically lubricated.
Use only new bar and chain oil or unused SAE 30 weight motor oil
may be substituted. Never use wasted oil, low quality oil, or
insufficient oil. This could damage the pump; the bar and the chain
which may result in serious personal injury.
Check oil level before each work session, refill if less than ¼ full.
If the lubrication system does not work properly, check if the oil filter
and all oil-ways are clean and free from obstructions. If it is still not
working, call our customer service help line at 1-800-313-5111 for
assistance.
GUIDE BAR MAINTENANCE
When the guide bar shows signs of wear, reverse it on the saw to
distribute the wear for maximum bar life. The bar should be cleaned
every day of use and checked for wear and damage.
Store the tool in a dry, clean area out of reach of children.
During extended periods of storage, ensure that the tool is
protected against corrosion and rust.
MAINTENANCE
Feathering or burring of the bar rails is a normal process of bar wear.
Such faults should be smoothed with a file as soon as they occur.
A bar with any of the following faults should be replaced.
- Wear inside the bar rails which permits the chain to lay over
side ways.
- Bent guide bar
- Cracked or broken rails
- Spread rails
In addition, guide bars with a sprocket at their tip must be lubricated
frequently with a grease syringe to extend the guide bar life. Using a
grease syringe, lubricate weekly in the lubricating hole.
Turn the guide bar and check that the lubrication holes and chain
groove are free from obstructions.
LUBRICATION SYSTEM FOR HEDGE TRIMMER (Fig. 24)
The cutting blades are made from high quality, hardened steel and
with normal usage, they will not require re-sharpening. However, if
you accidentally hit a wire fence, stones, glass or other hard objects,
you may put a nick in the blade. There is no need to remove this nick
as long as it doesn't interfere with the movement of the blade. If it
does interfere, make sure the unit is detached from the power supply
and use a fine toothed file or sharpening stone to remove the nick.
Fertilizers and other garden chemicals contain agents which greatly
accelerate the corrosion of metals Do not store the tool on or
adjacent to fertilizers or chemicals.
LUBRICATE BLADES - Stop the unit and disconnect the power cord.
Then remove any debris on blades. Apply a light machine oil along
the edge of the top and bottom blade supports. Make sure handles
remain clean and dry.
FIG.24
STORAGE
At the end of the season, or if the tool is not being used for
longer than a month, wipe over all metal surfaces with an oil
impregnated cloth to protect them from corrosion or spray
with a fine coat of oil.
13
Model CVP41810BB