GE GXSF30H Manual Del Propietario E Instrucciones De Instalación página 11

Installation Instructions
SET WATER HARDNESS NUMBER (CONT.)
3. When the displag shows gour water hardness
(in grains per gallon), press MODE to accept.
NOTE: If there is clear water iron in your water
supply, you will need to increase the hardness
setting bg 5 for each 1 ppm of clearwater iron
in your water supply.
You can get the grains per gallon (gpg} hardness
of your water supply from a water analysis
laboratory. If you are on a municipal supply,
call your local water department. Or call Legend
Technical Services, an independent laboratory,
to request a water hardness test kit at
1.800.949.8220, option 4. If your report shows
hardness in parts per million (ppm) or milligrams
per liter (rag/I), simply divide by 17.1 to get the
equivalent number of grains per gallon.
SET RECHARGE (STARTING) TIME
1. Press the MODE button until r
RECHARGE TIME appears in the
/ _-I.rll-I "M
d isplag, k................................. _°;_i:u .............................
NOTE: A flashing 2:00 AM (factorg
default) should show in the displag. This is a good
time for recharge to start (takes about 2 hours)
in most households because water is not in use.
HARD WATER is bgpassed to house faucets during
recharge.
If no change is needed, go to step 3. To change the
recharge starting time, follow step 2.
2. Press UP • or DOWN • button to set the desired
recharge start time. Be sure to observe the AM or
PM as gou did when setting the time of dag.
NOTE: Each press of a button changes the time bg
1 hour. Holding the buttons in changes the time at
a rapid rate.
3. Press the MODE button to accept.
11
OPTIONAL CONTROL SETTINGS
The controller displag has several options and
features.
SYSTEM/ELECTRONIC DIAGNOSTICS
This display contains system
diagnostics information to assist in
troubleshooting problems with the
Water Softener. See page 17.
nnn P
!_1 IJ LJ --
OR
To access the Sgstem Diagnostics, press and hold
the MODE button for 3 seconds.
To return to the normal displag, press the MODE
button 2 times.
SALT EFFICIENCY
When the SALT EFFICIENCY feature is ON, the
unit will operate at a salt efficiencg of at least 4000
grains of hardness removed per pound of salt. This
mode of operation is the most efficient setting for
salt usage, because the sgstem will tend to recharge
more often, with less salt usage. Turning the feature
OFF will tend to lengthen the time between recharge
cgcles, which will provide the most efficient usage
of water, but nag use more salt. The degree of
difference between these two cgcles is highlg
dependent on the water usage and hardness
at a particular installation.
NOTE: California Regulations require this feature to
be ON for installations in California.
To access the Salt Efficiencg,
press and hold the MODE
button for 3 seconds. The Sgstem
Diagnostics displag will appear.
Press the MODE button
again
and
the Salt Efficiencg displag will
appear.
LT,-,
NCC
urr
To change the setting, press the
UP
•
or DOWN • buttons to toggle the feature
ON or OFK Press the MODE button to accept.
ERROR SIGNALS
If there is an error code detected,
the displag will flash Err to signal
that the softener requires service.
Er rl] I
See page Z6 for information to
assist in troubleshooting error codes. Once the
problem is corrected, disconnect the transformer
from the wall outlet momentarilg, and plug it back
in. The normal displag will appear. The motor mag
run for several minutes, as the unit resets. If the
problem is not corrected, the error code will
reappear in 6 minutes.