Publicidad
Idiomas disponibles
Idiomas disponibles
Using the AC Plug (Fig. E)
CAUTION: Only use either a NEMA 1-15R or a
NEMA 5-15R power cord.
When not using a battery, you can use an extension cord
plugged into the AC plug
work light
1
.
nOTE: The adjustable work light is not a battery charger.
Using the AC plug will not charge your batteries.
1. Pull open the AC plug door
2. When a powered extension cord
adjustable work light
will illuminate.
nOTE: If a battery is connected to the adjustable
work light
1
when also using an extension cord, the
DWST08060 will only use power from the powered
extension cord.
3. If the articulating head LEDs
is connected to adjustable work light
work light
1
will automatically switch to AC power
mode without interruption. If the powered extension
cord is removed, and a battery is still connected to the
device, then the adjustable work light will automatically
switch to battery power.
4. To keep the AC plug
the extension cord and then close the AC plug door
securely when not in use.
Positioning the Articulating Head LEDs
(Fig. A, F)
WARNING: Do not to attempt to operate the
articulating head LEDs in the closed position, or
with the lens facing the adjustable work light, as
the surface the light may get hot.
The articulating head LED
and swivels from 0°–270°.
nOTE: The adjustable work light is equipped with magnetic
sensors. If the articulating head LED
lens facing the adjustable work light, the articulating head
LED
3
,
5
will not turn on and will turn off automatically.
1. To move the left articulating head LED
articulating head LED
from the adjustable work light
2. To adjust the light beam, swivel the left articulating head
LED
5
or right articulating head LED
the desired position.
3. When not in use fold the left articulating head LED
right articulating head LED
into the stored position, secured in the adjustable
work light
1
.
On/Off Switch (Fig. A, G)
WARNING: The lens gets very hot during use. To
reduce the risk of burns, do not touch hot lens.
WARNING: Keep objects at least 20" (51 cm) away
from the lenses when they are in use to prevent
the objects from overheating.
23
to power the adjustable
9
to access the AC plug
26
is connected to the
1
, the green AC LED indicator
3
,
5
is on and AC power
1
, the adjustable
23
safe from moisture, remove
3
,
5
piviots up and down 0°–160°
3
,
5
is stored with the
5
or right
3
first pull it upwards and away
1
.
3
by twisting it into
3
with the lens side facing
WARNING: To reduce the risk of fire, keep away
from combustible materials while in operation.
CAUTION: Do not stare into box light lens. Serious
eye injury could result.
nOTE: For best results, make sure your battery pack is fully charged.
1. To turn on the right articulating head LED
right LED On/Off button
2. To turn on the left articulating head LED
LED On/Off button
23
.
3. Each articulating head LED
levels, up to 2000 lumens. Continue to press the On/Off
18
buttons
2
4. Continue cycling the On/Off buttons until the lights turn off.
nOTE: The light box is equipped with magnetic sensors.
If the articulating head LED
facing the light box, the articulating head LED
not turn on and will tun off automatically.
Low Battery Indicator
As the battery nears a fully discharged state, the light will
blink twice. The light will continue to blink twice every 45
seconds until the battery is fully discharged at which time
the light will turn off. Indication time will vary based on
battery pack capacity.
CAUTION: Stop work and replace the battery when
9
this occurs.
Thermal Protection Mode
In cases of overheating, the articulating head LEDs
lumen output automatically switches to the next lower
brightness setting. If the temperature continues to increase,
the light box will power off until a normal operating
temperature is reached.
Top Handle (Fig. A)
This adjustable work light
that allows you to carry the adjustable work light
not attached to the storage compartment
Carry Handle (Fig. H)
This DWST08060 has a built in carry handle
you to carry the storage compartment
attached to a adjustable work light
Storage Compartment (Fig. I)
WARNING: Avoid overfilling the
storage compartment.
5
or
WARNING: Do not forcefully attach the adjustable
work light onto the storage compartment. If the
adjustable work light will not fully close or the latches
will not lock easily, ensure the storage compartment is
not overfilled. Remove a few items and try attaching the
adjustable work light again. If needed you can stack the
storage compartment on top of the adjustable work light.
WARNING: When stacking an additional ToughSystem®
2.0 unit on top of the adjustable work light, the battery
must be removed first, unless it is smaller than 6Ah.
2
.
4
.
3
,
5
has three brightness
,
4
to change the brightness level.
3
,
5
is stored with the lens
1
has a built in top handle
1
.
English
3
, press the
5
, press the left
3
,
5
will
3
,
5
10
1
when
15
.
14
that allows
15
when not
9
Publicidad
