Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT
Please read
these
instructions carefully before you start to assemble this product.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these
instructions
in
a
safe
place for
future
reference.
Safety advice
For
safety purposes we
strongly recommend the product to
be
assembled by at least
two
people.
Be
sure
to check that there
are no
hidden pipes or cables
in
the wall before drilling.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves,
eye
protection,
and long
sleeves
when assembling or performing any maintenance on
your product.
Do
not attempt to
assemble the
product
in
windy or wet conditions.
Do
not attempt to
assemble the
product if you
are
tired,
have
taken drugs, medications or
alcohol, or if you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children away from the assembly
area.
When using
a
stepladder or power
tools, make
sure
that you
are
following
the manufacturer's
safety advice.
Do
not climb or
stand on
the
roof.
Do
not
hang or
lay on
the profiles.
Heavy articles should not
be
leaned against the poles.
Keep
roof and gutters
clear
of
snow,
dirt
& leaves.
Heavy
snow load on the roof
can make
it unsafe to stand below or nearby.
If
color
was
scratched
during
assembly it can be fixed.
Cleaning
instructions
In
order to
clean
the product,
use
a
mild detergent solution and rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product once assembly
is
complete.
Before Assembly
Choose
your
site
carefully before beginning
assembly.
The
ground
surface must
be
perfectly flat
and leveled and have
a
solid
base such
as
concrete, asphalt, deck
etc.
Consider the door's opening (inside or outside).
Sort
the
parts and check against the
content
parts
list.
Parts
should
be
laid
out
close at hand. Keep
all
small parts (screws etc.) in
a
bowl
so
they do not
get
lost.
Please
consult your
local
authorities if any permits
are
required prior to constructing the product.
Additional information
Please
apply silicone sealant if needed
During assembly,
use
a
soft surface below the parts to avoid scratches and damages.
You are
solely responsible for
determining whether the handling,
storage, assembly,
installation
or
use
of
this product
is
safe
and
appropriate
in
any
location or for any given application.
The
manufacturer
is
not responsible for any damages or injury to you, any other person or any property
resulting from the improper handling, storage, installation, assembly or
use
of this product, or
the failure to follow the manufacturer's written instructions regarding the handling,
storage,
installation, assembly and
use
of
this product.
This
product
is
intended for normal residential
use
only.
Do
not
use
this product for any application that
is
not recommended
in
these
instructions or building
codes
in
effect
in
location where this product will
be used.
Always take
care
and
use
appropriate
safety
equipment (including
eye
protection) when assembling or
installing this product.
During Assembly
When
encountering the information
icon, please refer
to the relevant
assembly step for additional comments and
assistance.
Step
1: Before
assembling this product, choose one of the
7
assembly
options
and refer
to
sizes A &
B
of
the chosen option.
Step
3:
Important!
Please
make
sure
the back beam
is
perfectly centered before fixing,
height
A
should
be in accordance
with your
chosen
option from
step
1.
Step 4:
Please
apply silicone sealants above beam 8158,
in
order to prevent water from
seeping
in.
Step
7: Assemble
diagram
a
in
accordance
with your
chosen
option from
step
1.
Step 8:
Brackets can be
adjusted from
5
to
30
cm
(2"to
12")
as
suggested
in
diagram
a.
Step
10: Before
anchoring, please
tighten
all screws
(as
shown in the close up diagrams
b
&
c),
level
the profiles'
legs
(diagram
a)
and adapt screws and plugs
to your
specific
ground type.
Please
note:
Anchoring this product to the ground
is
essential to
its
stability
and rigidity.
It
is
required to complete this
stage
(Step 10)
in
order for your warranty to
be
valid.
Step
19:
Please
apply silicone sealants on the inner part
of Profile 8157,
and connect part 8167
as
depicted
in
drawing
a.
* Please
tighten
all screws
when completing assembly.
Note:
The
wall anchoring kit supplied
with
this product
is
suitable for concrete or solid
brick
walls.
Other wall types need
an
accordant wall fixation kit.
Anchoring this product to the ground
is
essential to its
stability
and rigidity.
It
is
required to complete this stage
in
order for your warranty to
be
valid.
Do
not tighten
screws
and nuts until completion of assembly
process.
These
2
icons
indicate if screws'tightening
is
required or not.
A
Publicidad
