Descargar Imprimir esta página

Craftsman 917.28810 Manual Del Operador página 14

Publicidad

Idiomas disponibles

Idiomas disponibles

• The average
lawn should
be cut to approxi-
mately 2-1/2 inches during the cool season
and to over 3 inches
during
hot months.
For healthier
and
better
looking
lawns,
mow
often
and
after
moderate
growth.
For best cutting
performance,
grass
over 6 inches
in height
should
be
mowed
twice.
Make the first cut rela-
tively
high; the second
to desired
height.
TO OPERATE
MOWER
Your tractor
is equipped
with an operator
presence
sensing
switch.
Any attempt
by the operator
to leave
the seat with the
engine
running
and the attachment
clutch
engaged
will shut off the engine.
You must
remain
fully and centrally
positioned
in the
seat to prevent
the engine
from hesitating
or cutting
off when
operating
your equip-
ment on rough,
rolling
terrain
or hills.
1.
Select
desired
height
of cut.
2.
Start mower
blades
by engaging
at-
tachment
clutch
control.
TO STOP
MOWER
BLADES-
disengage
attachment
clutch
control.
_CAUTION:
Do not operate
the mower
without
either
the entire
grass catcher,
on mowers
so equipped,
or the deflector
shield
in place.
Attachment
Attachemnt
Clutch Lever
Lift Lever
"Engaged"
High
Position
Position
Position
"Disengag
Position
Deflector
OPERATING
IN REVERSE
Your tractor
is equipped
with a Reverse
Operation
System
(ROS).
Any attempt
by
the operator
to travel
in the reverse
direc-
tion with the attachment
clutch
engaged
will shut off the engine
unless
the ignition
key is placed
in the ROS "ON" position.
ROS "ON" Position
Engine "ON" Position
(Normal Operation)
,_WARNING:
Backing
up with the at-
tachment
clutch
engaged
while
mowing
is strongly
discouraged.
Turning
the ROS
"ON", to allow
reverse
operation
with the
attachment
clutch
engaged,
should
only
be done when the operator
decides
it is
necessary
to reposition
the machine
with
the attachment
engaged.
Do not mow
in
reverse
unless
absolutely
necessary.
USING
THE
REVERSE
OPERATION
SYSTEM
-
1.
Move
motion
control
lever to neutral
position.
2.
With
engine
running,
turn
ignition
key
counterclockwise
to ROS "ON" position.
3.
Look down
and behind
before
and
while
backing
up.
4.
Slowly
move
motion
control
lever to
reverse
(R) position
to start
movement.
5.
When
use of the ROS is no longer
needed,
turn the ignition
key clockwise
to engine
"ON" position.
TO OPERATE ON HILLS
_bWARNING:
Do not drive up or down
hills with slopes greater than 15 ° and do
not drive across any slope. Use the slope
guide at the back of this manual.
• Choose the slowest speed
before start-
ing up or down hills.
• Avoid stopping or changing speed on hills.
• If slowing is necessary, move throttle
control lever to slower position.
• If stopping is absolutely necessary,
push
clutch/brake
pedal quickly to brake posi-
tion and engage parking brake.
• Move motion control lever to neutral
position.
IMPORTANT:
The motion control lever
does not return to neutral position when
the clutch/brake
pedal is depressed.
• To restart movement,
slowly release
parking brake and clutch/brake
pedal.
• Slowly move motion control lever to
slowest setting.
• Make all turns slowly.
TO TRANSPORT
When pushing or towing your tractor, be
sure to disengage
transmission
by placing
freewheel
control in freewheeling
position.
Freewheel control is located at the rear
drawbar of tractor.
1. Raise attachment
lift to highest posi-
tion with attachment
lift control.
2. Pull freewheel
control out and down
into the slot and release so it is held in
the disengaged
position.
14

Publicidad

loading