Descargar Imprimir esta página

Craftsman 917.28810 Manual Del Operador página 26

Publicidad

Idiomas disponibles

Idiomas disponibles

NOTE:
If additional
clearance
is needed
to get to adjustment
bolt, move
mower
deck
height
to the lowest
position.
After above
adjustment
is made,
if the
tractor
still creeps
forward
or backward
while
motion
control
lever is in neutral
position,
follow
these
steps:
1.
Loosen
the adjustment
bolt.
2.
Movethe
motion
control
lever 1/4 to 1/2
inch in the direction
it is trying to creep.
3.
Tighten
adjustment
bolt securely.
4.
Start engine
and test.
5.
If tractor
still creeps,
repeat
above
steps
until satisfied.
TRANSMISSION
REMOVAL/
REPLACEMENT
Should your transmission require removal for
service or replacement, it should be purged
after reinstallation and before operating the
tractor. See "PURGE TRANSMISSION"
in
the Operation section of this manual.
TO ADJUST
STEERING
WHEEL
ALIGN-
MENT
If steering
wheel
crossbars
are not
horizontal
(left to right)
when wheels
are
positioned
straight
forward,
remove
steer-
ing wheel
and reassemble
with crossbars
horizontal.
Tighten
securely.
FRONT
WHEEL
TOE-IN/CAMBER
The front wheel
toe-in
and camber
are not
adjustable
on your tractor.
If damage
has
occurred
to affect the front wheel
toe-in
or
camber,
contact
a Sears
or other
qualified
service
center.
TO REMOVE
WHEEL
FOR REPAIRS
,
2.
Block
up axle securely.
Remove
axle cover, retaining
ring and
washers
to allow wheel
removal
(rear
wheels
have a square
key - Do not lose).
Washers
Retaining Ring
Axle Cover
\
Square Key Only)_'
(Rear Wheel
3.
Repair
tire and reassemble.
NOTE:
On rear wheels
only:
align
grooves
in rear wheel
hub and axle.
Insert
square
key.
4.
Replace
washers
and snap
retaining
ring securely
in axle groove.
5.
Replace
axle cover.
NOTE:
To seal tire punctures
and prevent
flat tires due to slow leaks,
purchase
and
use tire sealant
from
Sears.
Tire sealant
also prevents
tire dry rot and corrosion.
TO START
ENGINE
WITH
A WEAK
BAT-
TERY
_WARNING:
Lead-acid
batteries
generate
explosive
gases.
Keep sparks,
flame
and smoking
materials
away from
batteries.
Always
wear
eye protection
when
around
batteries.
If your battery
is too weak to start the
engine,
it should
be recharged.
(See "BAT-
TERY"
in the MAINTENANCE
section
of
this manual).
If "jumper
cables"
are used for emergency
starting,
follow this procedure:
IMPORTANT:
Your tractor
is equipped
with a 12 volt system.
The other
vehicle
must also be a 12 volt system.
Do not use
your tractor
battery
to start other
vehicles.
TO ATTACH
JUMPER
CABLES
-
1. Connect one end of the RED cable
to the POSITIVE
(+) terminal of each
battery(A-B),
taking care not to short
against tractor chassis.
2. Connect one end of the BLACK cable
to the NEGATIVE
(-) terminal (C) of
fully charged battery.
3. Connect the other end of the BLACK
cable (D) to good chassis ground,
away from fuel tank and battery.
02614
Weak or Dead Battery
Fully Charged
Battery
TO REMOVE CABLES, REVERSE
ORDER -
1. BLACK cable first from chassis and
then from the fully charged battery.
2. RED cable last from both batteries.
26

Publicidad

loading