Publicidad
Idiomas disponibles
Idiomas disponibles
( 2 )
The Alarm button serves two purposes:
Alarm
- To turn the door open alarm on and off
/ Filter
- To reset the water fi lter life indicator.
Reset
(3sec)
1. Door Alarm Function
If the door alarm is set to On, an alarm
beeps if any refrigerator door is left open
for more than three minutes.
The beeping stops when you close the
door.
The door alarm function is pre-set to On in
the factory.
You can turn it off by pressing and then
releasing the Alarm button.
You can turn it back on in the same
fashion.
The icon lights up when the function is on.
When the Door Alarm function is on and
the alarm sound is triggered, the Door
Alarm Icon will blink while the alarm
sounds.
2. Water Filter Life Indicator Function
After you replace the water fi lter, touch and
hold this button for 3 seconds to reset the
water fi lter life indicator.
When you reset the water fi lter life indicator,
the Filter icon on the panel turns Off.
The Filter icon will turn red to let you know
it is time to change the water fi lter after six
months (about 300 gallons).
Some areas have large amounts of lime in
their water, which causes the water fi lter to
clog more quickly.
If this is the case in your area, you will have
to change the fi lter more frequently than
every six months.
( 3 )
The Energy Saver/Override (3sec) button
serves two purposes:
Energy
Saver /
- To turn the Energy Saver function on
Override
and off.
(3sec)
- To turn the Override function on and off.
1. Energy Saver function
Touching this button turns Energy Saver
mode on and off.
When you turn Energy Saver on, the
Energy Saver icon lights.
Turn Energy Saver off and the icon goes
off.
The Energy Saver function automatically
turns on when power is supplied to the
refrigerator.
If condensation or water drops appear on
the doors, turn the Energy Saver mode off.
2. Override function
The Override function activates/deactivates
Smart Grid (page 25). Press the Energy
Saver/Override button for 3 seconds to
set/clear the Override function.
DA68-02954B-03.indb 21
DA68-02954B-03.indb 21
( 4 )
The Fridge button serves two purposes:
Fridge /
- To set the Fridge to your desired
Power
temperature.
Cool
- To turn the Power Cool function on
(3sec)
and off.
1. To set the Fridge temperature, press
the Fridge button.
You can set the temperature between
44 °F (7 °C) and 34 °F (1 °C).
2. Power Cool function
Touch and hold this button for 3 seconds
to decrease the time needed to cool
products in the Refrigerator.
It can be helpful if you need to quickly cool
easily spoiled items or if the temperature in
the fridge has warmed dramatically.
(for example, if the door was left open)
( 5 )
The Lighting button serves two purposes:
Lighting
- To turn the dispenser light on and off
/ °C↔°F
- To switch the temperature units
(3sec)
between ºC and ºF.
1. Light Function
Touching the Lighting button turns on the
Dispenser LED lamp in continuous mode
so that it stays on continuously.
The button also lights up.
If you want the Dispenser lamp to come on
only when some one uses the dispenser,
press the Lighting button to turn the
continuous mode off.
2. To switch the temperature units
between ºC and ºF.
Touch and hold this button for 3 seconds
to select the temperature display you want.
Each time you press and hold the button,
the ºC and ºF temperature modes alternate
and the ºC or ºF icon lights up, indicating
your selection.
English - 21
2015. 2. 10.
2015. 2. 10.
3:38
3:38
Publicidad
