Publicidad
Idiomas disponibles
Idiomas disponibles
III. Explanation of LCD Information
A. The below picture highlights the LCD features
WWVB reception indicator
TIME
Radio-controlled time
WWWB
Sunrise time for
SUNRISE
MOON PHASE
selected location
Sunset time for
PM
selected location
SUNSET
City code for city selected
(San Francisco, USA shown)
INDOOR TEMPERATURE
Indoor temperature
TENDENCY
Air pressure tendency arrow
(increase displayed)
Relative or absolute air pressure
selection (relative shown)
PRESSURE
rel
Barometric air pressure
PRESSURE HISTORY
Pressure change over
last two hours (in hPa)
-30h
-24h
-18h
-12h
(+4 hPa shown)
OUTDOOR TEMPERATURE
Remote temperature
Remote temperature
LO
HI
minimum and maximum
MIN
MAX
OR alarm setting
B. There are many different modes the indoor weather station can be set to. The LCD shown
is the normal operating mode, and your actual data shown will be different based on your
local settings and conditions.
IV. Function Key Layout
A. The below picture shows the eight function keys used in programming and operation of
your indoor weather station.
OUTDOOR TEMPERATURE
IN
LO
HI
MIN
MAX
OUT
ALARM
SET
R A D I O C O N T R O L L E D
W E A T H E R S T A T I O N
V. Program Mode
The program mode is laid out in a manner that allows you to program each function separately,
or you can follow the instructions entirely to program the indoor weather center. Complete
programming is usually done for the initial set-up, and will require you to skip step 1 and 2 of
each programming section. The programming mode can be exited at any time by either pressing
the "CH" button, or waiting for the 16-second time-out to take effect.
GB
P.6
Alarm on indicator
DATE
Radio-controlled date
MOONRISE +1
Moonset time for
selected location
Current moon phase
PM
Moonset time for
selected location
LOCATION
MOONSET
HUMIDITY
%
Indoor humidity
RH
Comfort icon
Forecast icon
inHg
Measuring unit for
air pressure, inHg
shown
+7
+5
+3
+1
Last 30 hour air
0
-1
-3
pressure graph
-5
-7
-9h
-6h
-3h
-1h
01
+4
+1
+2
0
+0.2 +0.5
HUMIDITY
Remote humidity
%
2
RH
Remote sensor number
(up to three total)
%
%
RH
RH
Remote humidity
MIN
MAX
minimum and maximum
HUMIDITY
%
2
RH
SUN /
MOON
%
%
RH
RH
MIN
MAX
CH
+
A. Overview of programming mode sequence
Note : If the country setting is other than USA step 8 is city, step 9 is time zone, etc.
1. Hour
2. Minute
5. Month
6. Date
9. City
10. Time Zone
13. inHg/hPa
14. Relative pressure
setting
17. Storm alarm
18. LCD contrast
on/off
B. Time, 12/24 Hour Mode and Date Setting
The WWVB signal will override any manual set time and date information. The time will be
based on the time zone selected.
1. Press and hold the " SET " button for 1 second.
2. The hour is now flashing.
3. Press and release the "+" or "-" button to select the current hour.
Note : In 12h mode "PM" will appear to the left of the time during PM hours. If the time is
not within the PM hours nothing will be displayed. Be sure to set the time to the correct AM/
PM time to ensure automatic reception.
4. Press the " SET " button to advance to the minute
5. The minute is now flashing.
6. Press and release the "+"or "-" button to select the current minute.
7. Press and release the " SET " button to advance to the 12/24-hour setting.
8. "12" is now flashing.
9. Press and release the "+"or "-" button to select either 12 (am/pm) or 24 hour (military)
time format.
10. Press and release the " SET " button to advance to the year setting.
11. The year is now flashing.
12. Press and release the "+"or "-" button to select the current year.
13. Press and release the " SET " button to advance to the month setting.
14. The month is now flashing.
15. Press and release the "+"or "-" button to select the current month.
16. Press and release the " SET " button to advance to the date setting.
17. The date is now flashing.
18. Press and release the "+"or "-" button to select the current date.
19. Press and release the " SET " button to advance to the location setting (skip steps 1 and
2 in section B if continuing).
C. City Location Setting
The list of the cities available is listed after this section.
1. Press and hold the " SET " button for 1 second.
2. Press and release the " SET " button 6 times.
3. The country location will flash (USA default/factory setting).
4. Press and release the "+"or "-" button to select the country (USA=United States,
CAN=Canada, MEX=Mexico).
5. Press and release the " SET " button to advance to the state setting (USA only) or the
city location (Canada or Mexico).
3. 12/24 hour
4. Year
7. Country
8. State
11. DST on/off
12. ˚F/˚C
15. Forecast
16.Storm warning
sensitivity
setting
19. LI on/off
GB
P.7
Publicidad
