Publicidad
Idiomas disponibles
Idiomas disponibles
3
Orient the template with the Fusion logo at the bottom of the
template.
4
Secure the template to the selected location.
5
Using a drill bit appropriate for the mounting surface, drill a
hole inside the dashed line on the template to prepare the
mounting surface for cutting.
6
Using a jigsaw or rotary tool, cut the mounting surface along
the inside of the line on the template.
7
Place the speaker in the cutout to test the fit.
8
If necessary, use a file and sandpaper to refine the size of
the cutout.
9
After the speaker fits correctly in the cutout, ensure the
mounting holes on the speaker line up with the pilot holes on
the template.
10
If the mounting holes on the speaker do not line up, mark the
new hole locations.
11
Using an appropriately sized drill bit for the mounting surface
and screw type, drill the holes.
12
Remove the template from the mounting surface.
13
Connect the speaker wires while observing polarity.
14
Push the wire into a retaining clip to relieve the tension on the
wire.
15
If necessary, connect the LED wires to the Sports model
speakers (see the following section).
16
Place the speaker in the cutout.
17
Secure the speaker to the mounting surface using the
included screws.
NOTE: Do not over tighten the screws, especially if the
mounting surface is not flat.
For Classic model speakers, attach the grill to the speaker front.
Sports Model Speakers LED Wiring
Connecting the LED Wires to the Sports Model Speakers
NOTE: This feature is available only on the Sports model
speakers.
You can control the color of the LEDs by the polarity of the LED
wires.
1
Using the hex key, loosen the screws on the wiring terminals
on the back of the speaker.
2
Connect the black and red wires to the terminal according to
the preferred LED color.
Blue LED
Black to negative (-)
Red to positive (+)
White LED
Black to positive (+)
Red to negative (-)
3
Using the hex key, tighten the screws on the wiring terminals.
4
Push the wire into a retaining clip to relieve the tension on the
wire.
Connecting the Sports Model Speakers LED Wires to Power
NOTE: This feature is available only on the Sports model
speakers.
Before you can connect the LED wires to the speakers, you
must connect the LED wires to the power source.
All 12 Vdc wiring to the LEDs must be fused at the power-source
end of your cable using a 3 A fuse. The red power (+) wire
should be connected to a 12 Vdc source through an isolator
switch or circuit breaker to turn the speaker LEDs on and off.
You can use the same isolator or circuit breaker controlling the
supply to your stereo, which allows you to turn the LEDs and the
stereo on and off at the same time.
If it is necessary to extend the red and black wires included with
the speakers, you should use 20 AWG (0.5 mm
1
Route the red power (+) and black ground (-) wires to the
battery and speaker.
2
Connect the black wire to the negative (-) battery terminal.
3
Connect the red wire to the positive (+) terminal through a 3
A fuse and isolator switch or circuit breaker.
Attaching the Grill to the Classic Model Speakers
NOTE: This feature is available only on the Classic model
speakers.
1
With the speakers mounted, hold the grill with the Fusion
logo at the bottom, or at the 6 o'clock position.
2
Turn the grill counter-clockwise about 10°, so the Fusion logo
is at the 5 o'clock position.
3
Place the grill on the rim of the speaker.
4
Twist the grill clockwise to secure it.
Speaker Information
True-Marine
™
Products
True-Marine products are subjected to rigorous environmental
testing under harsh marine conditions to surpass industry
guidelines for marine products.
Any product that bears the True-Marine stamp of assurance has
been designed for simplicity of use and combines the most
advanced marine technologies to deliver an industry leading
entertainment experience. All True-Marine products are
supported by the Fusion 3-year worldwide limited consumer
warranty. You can be assured Fusion stands by its products and
takes pride in delivering True-Marine quality products for your
vessel.
Optional LED Voltage Regulator
You can use an LED voltage regulator (optional accessory SG-
VREGLED) to regulate the battery voltage supply to the LED
lights. You can use the voltage regulator if you notice the levels
of brightness changing when you are running your engine,
charging, or using battery power only. The voltage regulator can
power the LEDs on up to ten Signature Series speakers or
subwoofers; for example four pairs of speakers and two
subwoofers.
Registering Your Signature Series
Help us better support you by completing our online registration
today.
• Go to www.fusionentertainment.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
2
) or thicker wire.
3
Publicidad
