Descargar Imprimir esta página

Craftsman 917.28842 Manual Del Operador página 18

Publicidad

Idiomas disponibles

Idiomas disponibles

4,
Pullbackthelockcollar ofthenozzle adapter
andpushtheadapter o ntothedeckwashout
port a ttheleftendofthemower d eck. R elease
thelockcollar t olocktheadapter o nthenozzle,
IMPORTANT: Tughoseensuringconnection is
secure,
5.
Turn the wateron.
6,
Whilesittingin the operator'spositionon
thetractor, r e-start t heengine andplacethe
throttleleverinthe Fast
position,
IMPORTANT: Recheck the areamaking certain
the areais clear.
_..,,.,_
Hose
NozzleAdapter_
Washout Port
7.
Move the tractor's PTO (Blade Engage) to
the ON position. Remain in the operator's
position
with the cutting deck engaged until
the deck is cleaned.
8.
Move the tractor's PTO (Blade Engage) to
the OFF position. Turn the ignition key to the
STOP position to turn the tractor's engine
off, Turn the water off.
9.
Pull back the lock collar of the nozzle adapter
to disconnect
the adapter from the nozzle
washout port.
10.
Move the tractor to a dry area, preferably a
concrete or paved area. Engage the mower
deck PTO to remove excess water and to
help dry before putting the tractor away.
WARNING: A broken or missing washout
fitting could expose you or others to thrown
objects from contact with the blade.
• Replace broken or missing washout fitting
immediately, prior to using mower again.
• Plug any holes in mower with bolts and
Iocknuts.
BATTERY
Your tractor
has a battery
charging
system
which
is sufficient
for normal
use.
How-
ever, periodic
charging
of the battery
with
an automotive
charger
will extend
its life.
• Keep battery
and terminals
clean.
• Keep battery
bolts tight.
• Keep small
vent holes open.
• Recharge
at 6-10 amperes
for 1 hour.
NOTE:
The original
equipment
battery
on
your tractor
is maintenance
free.
Do not
attempt
to open or remove
caps or covers.
Adding
or checking
level of electrolyte
is
not necessary.
TO CLEAN
BATTERY
AND TERMINALS
Corrosion
and dirt on the battery
and termi-
nals can cause the battery
to "leak" power.
1.
Disconnect
BLACK
battery
cable
first
then
RED
battery
cable
and remove
battery
from tractor.
2.
Rinse the battery with plain water and dry.
3.
Clean
terminals
and battery
cable
ends
with wire brush
until bright.
4.
Coat terminals
with grease
or petro-
leum jelly.
5.
Reinstall
battery
(See "REPLACING
BATTERY"
in the SERVICE
AND AD-
JUSTMENTS
section
of this manual).
TRANSAXLE
COOLING
The transmission
fan and cooling
fins should
be
kept
clean
to assure
proper
cooling.
Do not attempt
to clean
fan or transmis-
sion while
engine
is running
or while the
transmission
is hot. To prevent
possible
damage
to seals,
do not use high pressure
water
or steam
to clean
transaxle.
Inspect
cooling
fan to be sure fan blades
are intact
and clean.
Inspect
cooling
fins for dirt, grass
clip-
pings
and other materials.
To prevent
damage
to seals,
do not use com-
pressed
air or high pressure
sprayer
to
clean
cooling
fins.
TRANSAXLE
PUMP FLUID
The transaxle
was sealed
at the factory
and fluid
maintenance
is not required
for
the life of the transaxle.
Should
the trans-
axle ever leak or require
servicing,
contact
your nearest
Sears
or other
qualified
service
center.
V-BELTS
Check V-belts for deterioration
and wear after
100 hours of operation
and replace
if neces-
sary. The belts are not adjustable.
Replace
belts if they begin to slip from wear.
ENGINE
LUBRICATION
Only
use high quality
detergent
oil rated
with API service
classification
SG-SL.
Select
the oil's SAE viscosity
grade
according
to your expected
operating
temperature.
oi_ vi_c c_e_le
18

Publicidad

loading