Publicidad
Idiomas disponibles
Idiomas disponibles
Care & maintenance.
Cleaning the nutribullet
is easy,
®
simply place any of the pieces
(except for the Motor Base and
Extractor Blade) on the
TOP
RACK
of the dishwasher or hand
wash with warm soapy water
and rinse.
Here's how to clean
the nutribullet
:
®
STEP 1:
The most important
thing — ALWAYS UNPLUG
the Motor Base from the
power supply outlet when
it is left unattended, before
assembling, disassembling,
changing accessories or
approaching parts that move
in use, or when cleaning.
Do not attempt to handle
the appliance until all parts
have stopped moving!
STEP 2:
Remove the nutribullet
Cup/
®
Extractor Blade assembly from
the Motor Base.
STEP 3:
Clean the individual components
(Motor Base, Extractor Blades,
nutribullet
Cups) as follows:
®
14
MOTOR BASE:
• For the most part, the Motor
Base doesn't really get dirty,
but if you neglect to twist
the Extractor Blade on to
the nutribullet
Cup tightly,
®
liquids can leak out and get
into the Motor Base and stick
to the activator buttons.
• To avoid risk of injury,
NEVER
use your hands or utensils
to clean the white actuator
Tabs while the nutribullet
®
is plugged in.
• Do not remove the rubber
or plastic liners inside the
Motor Base.
• Use a sponge or dish cloth
dampened with warm soapy
water to wipe down the inside
and outside of the Motor
Base until clean.
• Pay particular attention
to the white actuator tabs
on the inside of the Motor
Base to loosen any sticky
debris from drips and spills.
If necessary, you may use a
small brush to scrub the area
to ensure it is kept clean.
WARNING:
Never submerge
the Motor Base in water.
EXTRACTOR BLADE:
•
DO NOT REMOVE THE
GASKET
as this will
permanently damage the
Extractor Blade and cause
leakage. If after washing as
indicated above additional
disinfecting is desired,
you may rinse with a 10%
vinegar/water solution or
with lemon juice. If, over
time, the gasket becomes
loose or damaged, you may
order a new Extractor Blade
at nutribullet.mx
• Dry the Extractor Blade
completely. It is helpful to
turn the Extractor Blade on
its side in your dish drainer
to ensure
BOTH SIDES
of
the Extractor Blade are
completely dried.
NUTRIBULLET
CUPS
®
& TO-GO LIDS:
• These items are all
TOP
RACK
dishwasher safe. We
recommend rinsing them
and giving them a quick
brush with a dish brush to
remove any dried debris
before washing them in the
dishwasher.
NEVER
use the
sanitize cycle to wash the
nutribullet
Cups as this
®
may warp the plastic.
• Regularly check the 3
tabs on the side of the
nutribullet
Cups (cracking,
®
crazing, breakage or
rounding). If damaged,
replace immediately to
prevent possible personal
injury.
• NEVER USE A CUP WITH A
BROKEN, DAMAGED, OR
MISSING TAB AS DOING SO
MAY CAUSE THE CUP AND
MOTOR BASE TO SEPARATE
EXPOSING THE BLADE
ASSEMBLY!
STUBBORN CLEAN UP:
• If ingredients dry inside the
nutribullet
Cup, make your
®
cleanup a snap by filling the
cup about 2/3 full with room
temperature (21°C/70°F or
less) water and screw on the
Extractor Blade. Place the
nutribullet
Cup/Extractor
®
Blade assembly on the
nutribullet
Motor Base
®
for about 20-30 seconds.
This will loosen the stuck
ingredients, and with a light
scrub and rinse, you'll be all
finished.
Replacement parts.
To order additional parts and
accessories, please visit our
website at
nutribullet.mx
15
Publicidad
