Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING:
Always stop engine, disconnect spark
plug, a nd ground a gainst
engine before cleaning,
lubricating or doing any kind of maintenanceon your
machine.
Lubrication
1, Lubricatethe chipperchute hinge a with Nghtoil once a season,
2, Lubricatethe pivot pointson the chute deflectorwith lightoil oncea
season,
3, Referto the Briggs& StrattonOwner/Operator m anualpackedwith
yourunit forengine lubricationinstructions,
Engine
Care
Referto the Maintenancesectionof the Briggs& StrattonOwneUOp-
eratermanualpackedwith yourunit, Readand followinstructions
carefuNy.
1, Checkengine oil level beforeeach useas instructedin the
separateengine manual
2, Cleanair cleaner's preeleaner every25 hoursundernormal
conditions,Cleaneveryfew hoursunderextremelydustycondi-
tions,Replacetheair cleaner cartridge oncea season,To service
the air cleaner,referto theseparateenginemanual
3, Thespark plug shouldbe cleanedand the gap resetonce a
season,Referto the separateengine manualfor correctplugtype
and gap specifications,
\
i
s
4, Whenthe area is cleaned,pivotthe shredderscreendownwardand
re-securewith theclevis pin and hairpinclip removedearner,
5, Reattachthe debriscollectionbagto the chutedeflector,if desired,
Chipper
Shredder
Care
Beforeeach use,visuallyinspectyour chippershredderfor loose(or
missing)nuts and bolts, Securelytighten(or replace)all hardware
beforeoperatingthe chippershredder,
Cleaning
The Reduction
Chamber
WARNING:The impelleFs shredder blade and chipper
blades are sharp. Wear leather work gloves to protect
your hands when cleaning out the reduction chamber.
If the reductionchamberbecomescloggedwith debris,the shredder
screencan be pivotedupwardso that youcan cleanthe surrounding
area.Todo so, proceedas follows:
1, Stopengine,disconnectsparkplug,and makecertainthe chipper
shredderhascome to a completestop,
i_L
WARNING:The muffler and surrounding area will be
hot if the engine has been running. Use caution and
protest your hands if working near the muffler.
2, a, If attached,removedebrisbag,Removethetwo wingknobson
eithersideof the chute deflectorand pivotthe chute deflector
upward,See Figure8,
b, Removethe hairpinclip from the clevispin which extends
throughthe housingand shredderscreen,See Figure8,
Removeclevispin,
c, Pivotthe shredderscreenupwardand cleanthe surrounding
areaby scrapingawaydebris,
3, Confirmthat the sparkplug wire is disconnected and awayfrom
sparkplug, PuN on the starterropetwo-to-threetimesto purgeany
remainingdebrisfrom the reductionchamber
Sharpening
Or Replacing
Chipper
Blades
WARNING:The impelleFs chipper blades are sharp.
Wearleather work gloves to protect your hands.
1, Stopengine,disconnectspark plug,and makecertainthe chipper
shredderhascometo a completestop,
2, Pivot theshredderscreenupwardas instructedunderthe heading
Cleaningthe ReductionChamber,
3, a, Removethe chipperchute by removingthreehex nutsand
washerswhich secureit to the impellerhousing,See Figure9,
• Rotatethe impellerby hand untilone of the two chipperbladesis
visible throughthe impellerhousingopening,
b, Removethe blade by removing the internalhexscrews,lock
washersand hexnuts whichsecure it to the impeller,
NOTE:Use a 3/16" hexkey (Allen)wrenchon the outsideof the blade
and a 1/2" box(or socket)wrenchon the insideof the impeller,Hold
the Allen wrenchstationaryand rotatethe box(or socket)wrenchto
loosenthe nut.
4, Installa replacement(or sharpened)blade (PartNo, 742:0544A)
with the hardwareremovedearlier,
IMPORTANT: I f sharpeningthe blade,protecthandsby usinggloves,
Followthe originalangle of grind and makesureto removean equal
amountfrom eachblade,
5, To replacethe otherblade,rotatethe impellerto exposethe second
blade and repeatthe stepsabove,
10
Publicidad
